Bedienungsanleitung Stanley SM16 (Seite 16 von 104) (Englisch, Französisch, Türkisch)

720685

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH (Original Instructions)

– correct adjustment of the saw blade,

– dust extractor with air velocity not less than 20 m/s.

Ensure that the local extraction as well as hoods, baffles

and chutes are properly adjusted.

♦ Please be aware of the following factors influencing

exposure to noise:

– use saw blades designed to reduce the emitted

noise;

– use only well sharpened saw blades;

♦ Machine maintenance shall be conducted periodically;

♦ Machine faults, including guards or saw blade, shall be

reported as soon as they are discovered;

♦ Provide adequate general or localized lighting;

♦ Ensure the operator is adequately trained in the use,

adjustment and operation of the machine;

♦ Ensure that any spacers and spindle rings are suitable

for the purpose as stated in this manual.

♦ Refrain from removing any cut-offs or other parts of

the workpiece from the cutting area while the machine

is running and the saw head is not in the rest position

♦ Never cut workpieces shorter than 30 mm(Figure 34).

♦ Without additional support the machine is designed to

accept the maximum workpiece size of:

– Height 75 mm by width 140 mm by length 460 mm

– Longer workpieces need to be supported by suit-

able additional table(work support). Always clamp

the workpiece safely.

♦ In case of an accident or machine failure, immediately

turn the machine off and disconnect machine from the

power source.

♦ Report the failure and mark the machine in suitable

form to prevent other people from using the defective

machine.

♦ When the saw blade is blocked due to abnormal feed

force during cutting, turn the machine off and discon-

nect it from power supply. Remove the workpiece and

ensure that the saw blade runs free. Turn the machine

on and start new cutting operation with reduced feed

force.

♦ Never cut light alloy, especially magnesium.

♦ Whenever the situation allows, mount the machine to

a bench using bolts.

RESIDUAL RISKS

The following risks are inherent to the use of saws:

– injuries caused by touching the rotating parts

In spite of the application of the relevant safety reg-

ulations and the implementation of safety devices,

certain residual risks cannot be avoided. These are:

– Impairment of hearing.

– Risk of accidents caused by the uncovered parts of the

rotating saw blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed

when sawing wood, especially oak, beech and MDF.

The following factors increase the risk of breathing

problems:

– No dust extractor connected when sawing wood.

– Insufficient dust extraction caused by uncleaned exhaust

filters.

ELECTRICAL SAFETY

Only one voltage is applicable to this tool. Be sure to check

that the power supply corresponds to the voltage on the

rating plate.

Your Stanley tool is equipped with double insula-

tion, hence, it does not require to be earthed

When the power cord is damaged, have it sent

to a STANLEY service center for replacement to specially

prepared cables.

USING AN EXTENSION CABLE

If an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool

(see Technical Data).The minimum conductor size is 1.5

; the maximum length is 30 m. When using a cable

reel, always unwind the cable completely.

Cable cross-sectional

area (mm

)

Cable rated current

(Ampere)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rated current (Ampere)

110~127 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220-240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SM16 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info