Bedienungsanleitung Stanley SM16 (Seite 18 von 104) (Englisch, Französisch, Türkisch)

720685

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH (Original Instructions)

4. Install the saw blade (oo) onto the blade adaptor seated

directly against the inside arbor collar (rr), making sure

that the teeth at the bottom edge of the blade are point-

ing toward the back of the saw (away from the operator).

5. Replace the outer arbor collar (pp).

6. Tighten the blade locking screw (nn) carefully by turn-

ing counter-clockwise while holding the spindle lock

engaged with your other hand.

7. Return the guard bracket (ll) to its original position and

firmly tighten the guard bracket screw (kk) to hold brack-

et in place.

WARNING! Be aware the saw blade shall be

replaced in the described way only. Only use

saw blades as specified under Technical Data.

WARNING! The guard bracket(ll) must be

returned to its original position and the guard

bracket screw(kk) tightened before activating

the saw.

WARNING! Failure to do so may allow the guard

to contact the spinning saw blade resulting in

damage to the saw and severe personal injury.

Your mitre saw was accurately adjusted at the factory. If

readjustment due to shipping and handling or any other

reason is required, follow the steps below to adjust your

saw. Once made, these adjustments should remain

accurate.

Checking and Adjusting the Mitre Scale (Fig. 13,

14, 15)

1. Loosen the mitre lock knob (e), depress the mitre detent

(t) to release the mitre arm. Swing the mitre arm until the

latch locates it at the 0° mitre position. Do not lock mitre

lock knob (e).

2. Pull down the head until the blade just enters the saw

kerf (s).

3. Place a square (tt) against the left side fence (v) and

blade (oo) (Fig. 13).

WARNING: Do not touch the tips of the blade

teeth with the square.

If adjustment is required, proceed as follows:

4 . Loosen the mitre lock knob (e), depress the mitre detent

(t) to release the mitre arm. Swing the mitre arm until the

pointer points to 0° on the mitre scale. Tighten the mitre

lock knob (e).

5. Loosen the plastic knob (k) and use the wrench (i) to

loosen the fence stop screw (jj). Remove the left side

fence (v).

6. Pull down the head and lock it in the lowered position by

pushing in the lock down pin. Replace the left side fence

and place a square against the left side fence and the

blade. With the left side fence against the square use

the wrench (i) to tighten the hex bolts on the fence in the

order from the right side.

Checking and Adjusting the Blade to the Table

(Fig. 16–19)

♦ Use the supplied blade wrench(i) to mount the rear

support (mm) to the back of base(g).

♦ Mounting the mitre lock knob(e) to the mitre saw arm.

♦ Press down the operating handle (a) and pull out the

lock down pin (o), as shown.

♦ Gently release the downward pressure and allow the

arm to rise to its full height.

Bench Mounting (Fig. 6)

♦ Holes (j) are provided in all four feet to facilitate bench

mounting. Always mount your saw firmly to prevent

movement. To enhance the portability, the tool can be

mounted to a piece of 15 mm or thinner plywood which

can then be clamped to your work support or moved to

other job sites and reclamped.

♦ When mounting your saw to a piece of ply-

wood, make sure that the mounting screws

do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When

clamping the saw to any work surface, clamp only on

the clamping bosses where the mounting screw holes

are located. Clamping at any other point will interfere

with the proper operation of the saw.

♦ To prevent binding and inaccuracy, be sure the moun-

ting surface is not warped or otherwise uneven. If the

saw rocks on the surface, place a thin piece of material

under one saw foot until the saw is firm on the moun-

ting surface.

Mounting the Saw Blade (Fig. 9, 10, 11, 12)

WARNING: To reduce the risk of injury, turn unit

off and disconnect machine from power source

before installing and removing accessories,

before adjusting or changing set-ups or when

making repairs. Be sure the trigger switch is in the OFF

position. An accidental start-up can cause injury.

♦ Never depress the spindle lock button while the blade

is under power or coasting.

♦ Do not cut light alloy and ferrous metal (containing iron

or steel) or masonry or fibre cement product with this mitre

saw.

♦ Should use the corresponding blade cutting different

materials.

1. With the lower guard held in the raised position loosen

the guard bracket screw (kk) until the guard bracket (ll)

raises far enough to access the blade locking screw

(nn).

2. Depress the spindle lock button (x) with one hand and

with the other hand use the wrench (i) provided to

loosen the left-hand threaded blade locking screw (nn)

by turning clockwise.

WARNING: To use the spindle lock, press the

button as shown and rotate the spindle by hand

until you feel the lock engage.

Continue to hold the lock button in to keep the spindle from

turning.

3. Remove the blade locking screw (nn) and the outside

arbor collar (pp).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SM16 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info