Bedienungsanleitung Stanley SM16 (Seite 21 von 104) (Englisch, Französisch, Türkisch)

720685

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH (Original Instructions)

1. Loosen the mitre lock knob (e) and depress the mitre

detent (t). Move the head left or right to the required

angle.

2. The mitre detent will automatically locate at 0º, 15º,

22.5º , 31.6ºand 45º. if any intermediate angle or 52º

is required hold the head firmly and lock by tightening

the mitre lock knob (e).

3. Always ensure that the mitre lock lever is locked

tightly before cutting.

4. Proceed as for a vertical straight cross-cut.

WARNING: When mitring the end of a piece of

wood with a small off-cut, position the wood to

ensure that the off-cut is to the side of the blade

with the greater angle to the fence; i.e. left mitre,

off-cut to the right - right mitre, off-cut to the left.

Bevel Cuts (Fig. 1, 2, 27)

Bevel angles can be set from 0º right to 45° left and can be

cut with the mitre arm set between zero and a maximum of

45° mitre position right or left.

1. Loosen the left side fence clamping knob (k) and slide

the upper part of the left side fence (v) to the left as far

as it will go. Loosen the bevel clamp knob (p) and set

the bevel as desired.

2. Tighten the bevel clamp knob (p) firmly.

3. Proceed as for a vertical straight cross-cut.

Quality of Cuts

The smoothness of any cut depends on a number of

variables, e.g. the material being cut. When smoothest

cuts are desired for moulding and other precision work,

a sharp (60 tooth carbide) blade and a slower for wood,

a sharp (80-120 tooth carbide) blade and a slower for

aluminum, even cutting rate will produce the desired

results.

WARNING: Ensure that the material does not

creep while cutting; clamp it securely in place.

Always let the blade come to a full stop before

raising the arm. If small fibres of wood still split

out at the rear of the workpiece, stick a piece of masking

tape on the wood where the cut will be made. Saw through

the tape and carefully remove tape when finished.

Cutting Repetitive Lengths (Fig.20)

When cutting several pieces of stock to the same length,

ranging from 230 mm to 400 mm, use the set plate (ee).

Install the set plate on the holder (ee) as shown in the

figure 20.

Align the cutting line on your workpiece with either the

left or right side of the groove in the kerf board, and while

holding the workpiece, move the set plate flush against the

end of the workpiece.

Then secure the set plate with the screw.

When the set plate is not used, loosen the screw and turn

the set plate out of the way.

Clamping the Workpiece (Fig. 3, 7, 38)

1. Whenever possible, clamp the wood/ aluminum to the

saw.

2. For best results use the clamp (gg) made for use with

your saw. Clamp the workpiece to the fence whenever

possible. You can clamp to either side of the saw blade;

remember to position your clamp against a solid, flat

surface of fence.

3. Mounting the clamp: Inserting the vertical clamp to the

holes(mm) as shown in Figure 7, then rotate to the

right position. If horizontal clamp is needed, please

mounting the horizontal clamp to the holes(qq) as

shown in Figure 38.

WARNING: Always use a material clamp when

cutting non-ferrous metals.V

WARNING: Always use both of vertical clamp and

horizontal clamp when cutting small pieces.

Support for Long Pieces (Fig. 3, 8)

1. Always support long pieces.

2. For best results, use the extension work support (ii)

to extend the table width of your saw. Support long

workpieces using any convenient means such as

saw-horses or similar devices to keep the ends from

dropping.

3. Mounting the work support(Fig. 8):

Use the supplied blade wrench(i) to loosen the screws.

Insert the work support to the holes(h).

Tighten the screws.

Cutting Aluminum Extrusion

WARNING: Never attempt to cut thick or round

aluminum extrusions. Thick aluminum extrusions

may come loose during operation and round

aluminum extrusions cannot be secured firmly

with this tool.

When securing aluminum extrusions, use spacer blocks

or pieces of scrap as shown in the Fig.28 to prevent

deformation of the aluminum.Use a cutting lubricant when

cutting the aluminum extrusion to prevent build-up of the

aluminum material on the blade.

Cutting Picture Frames, Shadow Boxes and

Other Four-sided Projects (Fig. 29, 30)

Trim Moulding And Other Frames

Try a few simple projects using scrap wood until you

develop a “feel” for your saw. Your saw is the perfect tool

for mitring corners like the one shown in figure 30. The

joint shown has been made using either bevel adjustment.

Using Bevel Adjustment

The bevel for the two boards is adjusted to 45° each,

producing a 90° corner. The mitre arm is locked in the zero

position. The wood is positioned with the broad flat side

against the table and the narrow edge against the fence.

Using Mitre Adjustment

The same cut can be made by mitring right and left with the

broad surface against the fence.

The two sketches (Fig. 29, 30) are for four side objects

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SM16 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info