Bedienungsanleitung Stanley SM16 (Seite 23 von 104) (Englisch, Französisch, Türkisch)

720685

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH (Original Instructions)

3. Save the left side of the cut.

Outside Corner

Left side

1. Bottom of the moulding against the fence.

2. Mitre left.

3. Save the left side of the cut.

Right Side

1. Top of the moulding against the fence.

2. Mitre right.

3. Save the right side of the cut.

Special Cuts

♦ All cuts are made with the material secured to the

table and against the fence. Be sure to properly secure

workpiece.

Bowed Material (Fig. 35, 36)

When cutting bowed material always position it as shown

in Figure 35 and never like that shown in Figure 36.

Positioning the material incorrectly will cause it to pinch

the blade near the completion of the cut.

Cutting Plastic Pipe or Other Round Material

Plastic pipe can be easily cut with your saw. It should be

cut just like wood/ aluminum and clamped or held firmly

to the fence to keep it from rolling. This is extremely

important when making angle cuts.

Cutting Large Material (Fig. 37)

Occasionally a piece of wood will be too large to fit beneath

the blade guard. A little extra height can be gained by

rolling the guard up out of the way, as shown in Figure 37.

Avoid doing this as much as possible, but if need be, the

saw will operate properly and make the bigger cut. NEVER

TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN

WHEN OPERATING THIS SAW.

Dust Extraction (Fig. 2, 3)

Fit the dustbag (ff) onto the dust spout (n).

WARNING: Whenever possible, connect a dust

extraction device designed in accordance with

the relevant regulations regarding dust emission.

Connect a dust collection device designed in

accordance with the relevant regulations. The air velocity

of externally connected systems shall be 20 m/s ±2 m/s.

Velocity to be measured in the connection tube at the point

of connection, with the tool connected but not running.

Transporting (Fig. 4, 5)

In order to conveniently carry the mitre saw, a carrying

handle (m) has been included on the top of the saw arm.

♦ To transport the saw, lower the head and depress the

lock down pin (o).

♦ Always use the carrying handle (m) or the hand

indentations (r) shown in figure 5 to transport the saw.

Maintenance

MAINTENANCE

Your STANLEY power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

tool care and regular cleaning.

♦ Regularly clean the ventilation slots in your tool using

a soft brush or dry cloth.

♦ Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.This

machine is not user-serviceable. If problems occur

contact an authorised repair agent.

Lubrication

Closed-type, grease-sealed ball bearings are used

throughout. These bearings have sufficient lubrication

packed in them at the factory to last the life of the mitre

saw.

Cleaning

Before use, carefully check the upper blade guard,

movable lower blade guard as well as the dust extraction

tube to determine that it will operate properly. Ensure that

chips, dust or workpiece particle cannot lead to blockage

of one of the functions.

In case of workpiece fragments jammed between saw

blade and guards disconnect the machine from the

power supply and follow the instructions given in section

Mounting the Saw Blade. Remove the jammed parts and

reassembling the saw blade.

WARNING: Blow dirt and dust out of the main

housing with dry air as often as dirt is seen

collecting in and around the air vents. Wear

approved eye protection and approved dust

mask when performing this procedure.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the

materials used in these parts. Use a cloth

dampened only with water and mild soap. Never

let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

WARNING: To reduce the risk of injury,

regularly clean the table top.

WARNING: To reduce the risk of injury,

regularly clean the dust collection system.

To maintain products SAFETY and RELIABILITY,

repair, carbon brush inspection and replacement, any

other maintenance or adjustment should be performed

by STANLEY Service Centers, always using Stanley

replacement parts.

OPTIONAL ACCESSORIES

WARNING: Since accessories, other than those

offered by STANLEY, have not been tested with

this product, use of such accessories with this

tool could be hazardous. To reduce the risk of

injury, only STANLEY, recommended accessories should

be used with this product.

Consult your dealer for further information on the appro-

priate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SM16 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info