Bedienungsanleitung Stanley SPS-900 (Seite 12 von 36) (Deutsch, Englisch)

720577

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Do not touch the exhaust pipe, there is a risk of burns.

Only use the fuel recommended in the manual.

Keep gasoline only in containers designed for it,

and store it at a safe location.

While cutting on a slope, always stand below the

cutting tool.

Always make sure no objects or other debris is

collecting in the trimmer head, in the protective

hood, or in the engine.

Always switch o the tool before you put it down.

Do not use any wire, or anything similar in the line

spool.

Only work during daylight, or when the area is

illuminated well using articial lighting.

Subject the tool to a visual inspection before each

use.

Check, if all screws and connecting parts are

tightened.

Always use both hands to hold the tool.

Check the tool, and its components and guards for

damages, or wear and tear before each use, and have it

repaired, if necessary. Never make the

devices for protection and safety inoperable. Do

not use the tool, when damages or signs of wear

become apparent.

Keep the tools clean and fully functional to ensure

better and safer work.

Always maintain a safe distance between the tool

and your body during work.

Always switch o the tool when work will be

interrupted or the location will be changed; wait

until the cutting tools have completely stopped, a

nd turn o the engine.

Never leave the tool without supervision at the

place of work. Store the tool at a safe place when

work will be interrupted.

Persons operating the machine must not be

distracted, or one may lose control over the tool.

Never use the tool during rain, in a humid or wet

environment, and do not store it outdoors.

Should the tool become wet, wait until it is

completely dry before you use it again.

Before starting work, it is recommended to check

the objects to be cut for possible foreign objects

and to remove them. When despite of this you

encounter a foreign object during cutting, switch

o the tool and remove this object.

If the tool is jammed by a foreign object (stones,

piles of grass), switch it o, and remove the object

using a blunt item. Never use your ngers to

remove jammed foreign objects, because this may cause

serious injuries.

Always keep the running tool away from your body.

Attention: the cutting tool still runs for some time

after the tool is switched off!

Do not overload the engine, and do not use it for

work the tool is not designed for.

Always make sure the ventilation openings are free of

dirt.

Store the tool out of the reach of children.

Store the tool at a safe and dry location.

Check the engine for damages after impact, or other

damages.

Keep body parts and pieces of clothing away from the

trimmer head when you start the engine, or

keep it running.

Always keep in mind that especially during

trimming of lawn edges, gravel enclosures, and

similar locations stone and dirt can be hurled

away from the cutting line.

Never cross roads or paths when the tool is

switched on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SPS-900 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info