Bedienungsanleitung Stanley STDG5006 (Seite 6 von 11) (Englisch)

720783

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

d. Always feed the bit into the material in the same

direction as the cutting edge is exiting from the

material (which is the same direction as the chips

are thrown). Feeding the tool in the wrong direction

causes the cutting edge of the bit to climb out of the work

and pull the tool in the direction of this feed.

e. When using rotary ﬁles, cut-off wheels, highspeed

cutters or tungsten carbide cutters, always have the

work securely clamped. These wheels will grab if they

become slightly canted in the groove, and can kickback.

When a cut-off wheel grabs, the wheel itself usually

breaks. When a rotary ﬁle, highspeed cutter or tungsten

carbide cutter grabs, it may jump from the groove and

you could lose control of the tool.

Safety Warnings Speciﬁc For Grinding

Operations

a. Use only wheel types that are recommended for your

power tool and only for recommended applications.

For example: do not grind with the side of a cut-off

wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

b. For threaded abrasive cones and plugs use only

undamaged wheel mandrels with an unrelieved

shoulder ﬂange that are of correct size and length.

Proper mandrels will reduce the possibility of breakage.

c. Do not “jam” a cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or snagging of the

wheel in the cut and the possibility of kickback or wheel

breakage.

d. Do not position your hand in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your hand, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

e. When wheel pinched, snagged or when interrupting

a cut for any reason, switch off the power tool and

hold the power tool motionless until the wheel

comes to a complete stop. Never attempt to remove

the cut-off wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheel pinching or snagging.

f. Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

g. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

h. Use extra caution when making a “pocket cut”into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

Storage and handing of recommended accessories.

7. Electrical safety

Your tool is double insulated; therefore no earth wire

is required. Always check that the main voltage

corresponds to the voltage on the rating plate.

Warning! If the power cord is damaged, it must be

replaced by the manufacturer, authorized STANLEY

Service Center or an equally qualiﬁed person in

order to avoid damage or injury. If the power cord is

replaced by an equally qualiﬁed person, but not authorized

by STANLEY, the warranty will not be valid.

(Original instructions)

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

6. Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STDG5006 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info