Bedienungsanleitung Stanley STHR323 (Seite 7 von 11) (Englisch)

720462

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

(Original instructions)

Keyed chuck (ﬁg. D)

• Open the chuck by turning the sleeve (12)

anti-clockwise.

• Insert the bit shaft (13) into the chuck.

• Insert the chuck key (14) into each hole (15) in the side

of the chuck and turn clockwise until tight.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, ﬂoors or ceilings, check

for the location of wiring and pipes.

Warning! Do not apply chisels when the tool is in the drilling

mode.

Selecting the operating mode (ﬁg. F)

The tool can be used in three operating modes.

• To operate the drilling mode selector (3), rotate it

towards the required position, as indicated by the

symbols.

• To operate the operating mode selector (4), push the

unlock button (16) and rotate the selector towards the

required position, as indicated by the symbols.

Drilling

• For drilling in steel, wood and plastics, and for

screwdriving set the operating mode selector (4) to the

position and the drilling mode selector (3) to the

position.

Hammer drilling

• For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the position and the

drilling mode selector (3) to the position. When

hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

Hammering

• For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (4) to the

position and the drilling mode selector (3) to the

position.

• When changing from hammer drilling to chiselling, turn

the chisel to the desired position. If resistance is felt

during mode change, slightly turn the chisel to engage

the spindle lock.

Switching on and off

• Select the required speed by turning the speed selector

dial (2).

• To switch the tool on, press the on/off switch (1).

• To switch the tool off, release the on/off switch.

Brush monitor (ﬁg. E)

Your tool has a built in system that monitors the health of the

brushes.

• Green brush monitor indicator (17). The brushes are in

good condition.

• Red brush monitor indicator (18). The brushes are warn

and need replacing, return your tool to an authorised

STANLEY Service Centre in order to to have the brushes

replaced.

Accessories

The performance of your tool depends on the accessory

used. STANLEY and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you

will get the very best from your tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on

corded/cordless power tools:

• Switch off and unplug the appliance/tool.

• Regularly clean the ventilation slots in your

appliance/tool/charger using a soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

• Regularly open the chuck and tap it to remove any dust

from the interior (when ﬁtted).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STHR323 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info