720752
11
Zoom out
Zoom in
Vorherige Seite
1/226
Nächste Seite
11
GB
4.
Mark
a
on the center of the beam on the wall.
5.
Turn the laser 90º clockwise so that the left-most
end of the laser line is displayed near
a
(Figure
D
2
).
6.
Mark
b
on the center of the beam on the wall.
7.
Measure the vertical distance between
a
and
b
.
8.
If your measurement is greater than the
Allowable Distance Between
a
and
b
for the
corresponding Distance Between Walls in the
following table, the laser must be serviced at an
authorized service center.
Distance
Between Walls
Allowable Distance
Between
a
and
b
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30′ (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser against the end of the wall
(Figure
E
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
At least 30′ (9m) apart along the laser beam,
mark
a
and
b
.
4.
Move the laser to the opposite end of the wall
(Figure
E
2
).
5.
Position the laser toward the rst end of the same
wall and parallel to the adjacent wall.
6.
Adjust the height of the laser so the center of the
beam is aligned with
b
.
7.
Directly above or below
a
, mark
c
along the
laser beam (Figure
E
3
).
8.
Measure the distance between
a
and
c
.
9.
If your measurement is greater than the
Allowable Distance Between
a
and
c
for the
corresponding Distance Between
a
and
b
in
the following table, the laser must be serviced at
an authorized service center.
Distance Between
a
and
b
Allowable Distance
Between
a
and
c
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30′ (9m), with one person on the oor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
On the oor between two walls, mark a 5 ft.
(1.5 m) line that is parallel to the adjacent wall
(Figure
F
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
Place the laser at one end of the line on the oor,
making sure the vertical laser beam is aligned
and centered on the line.
4.
Where the vertical laser beam appears on the
ceiling, mark
a
. (This should be directly over the
midpoint of the line on the oor.)
5.
Move the laser to the other end of the line on the
oor (Figure
F
2
).
6.
Where the vertical laser beam appears on the
ceiling, mark
b
, directly beside the rst mark
a
.
7.
Measure the distance between
a
and
b
.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley STHT77498-1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info