720752
12
Zoom out
Zoom in
Vorherige Seite
1/226
Nächste Seite
12
GB
8.
If your measurement is greater than the
Allowable Distance Between
a
and
b
for the
corresponding Ceiling Height
D
in the following
table, the laser must be serviced at an authorized
service center.
Ceiling Height
D
Allowable Distance
Between
a
and
b
8′ (2.5m) 5/32" (3.5mm)
10′ (3.0m) 3/16” (4.5mm)
14′ (4.0m) 1/4” (6.0mm)
20′ (6.0m) 3/8” (9.0mm)
30′ (9.0m) 1/2” (13.0mm)
Using the Laser
Operating Tips
Always mark the center of the beam created by
the laser.
Extreme temperature changes may cause
movement of internal parts that can affect accuracy.
Check your accuracy often while working.
If the laser is ever dropped, check to make sure it
is still calibrated.
As long as the laser is properly calibrated, the
laser is self-leveling. Each laser is calibrated at
the factory to nd level as long as it is positioned
on a at surface within average ± 4° of level. No
manual adjustments are required.
Use the laser on a smooth, at, level, surface.
Turning the Laser Off
Slide the Power/Transport Lock switch to the OFF
position (Figure
A
2
) when the laser is not in use. If
the switch is not placed in the OFF position, the laser
will not turn off.
Using the Laser with the Bracket
A bracket (Figure
G
) is included with the laser so
you can easily attach the laser to a stud, ceiling grid,
or pole.
1.
Securely attach the laser to the bracket.
Using the 1/4-20 thread on the bottom, side,
or back of the laser (Figure
C
), position the
laser on the 1/4-20 thread on the bracket arm
(Figure
G
1
).
Turn the laser knob (Figure
G
2
) clockwise
to lock the laser on the 1/4-20 thread on the
bracket arm.
2.
If needed, change the height or position of the
laser on the bracket.
Turn the adjustment knob (Figure
G
3
)
counter-clockwise to loosen the bracket arm.
Slide the bracket arm up or down to the desired
height (Figure
G
4
). To change the bracket
from 90° to 180°, slide the bracket arm to the
top of the bracket and then flip the arm to the
right (Figure
G
5
).
Turn the adjustment knob (Figure
G
3
)
clockwise to lock the bracket arm in place.
3.
Use the bracket’s clamp (Figure
G
6
) to hold
the laser in place on a stud, ceiling grid, or pole.
If necessary, rotate the clamp so it is positioned
at the correct angle for attaching to the object.
While holding the bracket arm with one hand,
use your other hand to turn the clamp (Figure
G
7
).
Position the bracket’s clamp around the stud,
ceiling grid, or pole.
Turn the clamp knob (Figure
G
8
) clockwise
until the clamp is tight around the object and
the bracket is held in place.
Using the Laser with Other
Accessories
WARNING:
Since accessories other than those offered
by STANLEY have not been tested with this
laser, use of such accessories with this laser
could be hazardous.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley STHT77498-1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info