Bedienungsanleitung Starkwerk SW 4700 (Seite 18 von 24) (Deutsch, Englisch)

781907

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

VDE- and DIN provisions. Only use connecting cables

with the H 07 RN designation.

Keeping a copy of the type designation on the connect-

ing cable is a specication

Dmaged electric connecting cables

Insulation damages frequently occur on electric connect-

ing cables. The reasons are:

• Pressure points, if connecting cables are routed

through window or door gaps.

• Kinks due to improper mounting or routing of con-

necting cables.

• Intersections due to overruns of connecting cables.

• Insulation damage due to pulling out from wall sock-

ets.

• Cracks due to ageing of insulation.

Such damaged electric connecting cables should not be

used and can be fatal because of the insulation damage

AC motor 230 V/ 50 Hz

Mains voltage 230 Volt / 50 Hz.

Mains connection and extension cable must have

3-wires = P + N + SL. - (1/N/PE).

Extension cables must have a minimum cross-section of

1.5 mm².

The mains connection is secured with a max. 16A fuse.

Maintenance

Caution! Pull out power plug.

• Clean the machine after each work cycle.

• Replace worn out cutting discs.

• Replace damaged protection device

• Dust and pollution must be removed regularly from the

machine. The best way to clean the machine is with a

piece of cloth or brush.

• All moveable parts must be re-lubricated at periodic

intervals.

• Do not use any corrosive substances to clean the

plastic. A damp cloth is sufcient in most cases.

• The tub (4) and coolant pump (13) must be cleaned

regularly to remove dirt, as otherwise the pump or the

pipe or the cooling of the diamond cutting disc (10) is

not guaranteed.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the following

parts are therefore also required for use as consuma-

bles.

Wear parts*: Saw blade, carbon brush, table & cutting

head guides

* Not necessarily included in the scope of delivery!

Spare-part ordering

Please quote the following in your order for spare parts:

• Type of device

• Article No. of device

• Ident. No. of device

• Spare Part No. of the required spare part

Start-up of the leakage current circuit-breaker:

• The function should be checked before each start-up

and at regular Intervals (min. once every week).

• If the leakage current circuit-breaker does

not switch off properly during this test, there

is no personal protection! The device must

therefore be switched off immediately!

• In case of damages caused by the non-observation of

this operating instructions manual, all warranty claims

will become null and void. We do not accept any liabil-

ity for consequential damages.

• Check the product for damage before each use! If you

detect a damage, do not connect the product to the

mains power supply!

• After actuating the orange Reset button, the device

is ready for operation. Before operation, please test

the triggering with the help of the Test button (as de-

scribed in “Operation”).

• Insert the leakage current circuit-breaker into the

socket.

• Press the orange Reset button.

• A red symbol is displayed in the window indicating op-

erational readiness.

• Press the red Test button. This action simulates a

leakage current.

• If the machine is working properly, the circuit-breaker

will disconnect the load from the mains. This is dis-

played in the window through the disappearance of

the red symbol.

• Protection of man and animal is effective only if the

machine works properly.

• The Reset button must be pressed a second time for

operation.

• The load can now be inserted.

Technical data:

Triggering leakage current: < 30 mA

Power supply: 230V~/50Hz

Load capacity: 16A (3680W)

Number of pins: 2-pin wired

Preliminary fuse: 16 A

Protection type: IP54

Dimensions: 126x50x88mm

USE ACCORDING TO MANUFACTURER‘S INSTRUC-

TIONS!

The portable leakage current circuit-breaker is designed

for wet grinding machines and similar electrical loads in

the household.

It is simply connected between the mains power supply

and the load, and therefore offers optimum protection

against physical contact with live components and sud-

den restart of the machine after restoration of power.

• Always operate the machine with the provided leakage

current circuit-breaker installed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Starkwerk SW 4700 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info