Bedienungsanleitung Steinel DL 750 S (Seite 7 von 33) (Alle Sprachen)

593119

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

For exposed wiring 2:

drill the hole for insertion of

the cable and deburr with a

round file.

4. Screw on housing a, align

at a right angle if required

by means of the elongated

holes.

5. Connection of the mains

lead (see diagram).

The mains lead consists of a

3 phase cable (dia. 10 mm

max.).

L = phase conductor

(usually black

or brown)

N = neutral conductor

(usually blue)

PE = protective-earth

conductor

(green/yellow)

Principle

The CeilingSensorLight is

equipped with three 120°

pyro sensors which detect the

invisible heat emitted by mov-

ing objects (pedestrians, ani-

mals etc.). The heat detected

is converted electronically

into a signal that switches the

light on automatically. No

heat radiation is detected

through obstacles, such as

walls or glass and no

switching therefore occurs.

Pyro sensors have a detec-

tion angle of 360° with an

opening angle of 180°.

Safety instructions

Disconnect the power

supply before any work on

the CeilingSensorLight!

During installation, the

electric power cable to be

connected must be

voltage-free. Therefore,

switch off the power first

and check freedom from

voltage with a voltage

tester.

Installation of the

CeilingSensorLight

involves work on the

Installation

The installation site should be

at least 50 cm from another

light, since the latter's heat

radiation could result in false

triggering of the sensor.

Furthermore, the Ceiling-

SensorLight must be position-

ed completely on the attach-

ment surface.

Installation procedure:

1. Hold housing a against

the wall and mark drill

holes at the markings.

2. Drill the holes and insert

wall plugs (6 mm dia.).

3. Strip the insulation of the

mains lead, leaving 10 mm

of insulation and push the

enclosed heat-resistant

silicone tubes on to the

insulated conductors.

Insert the sealing plug into

the housing, pierce and

pass the cable through.

If in doubt, the cable must be

identified with a voltage test-

er. Switch off the current

again. The phase (L) and

neutral conductors (N) are

connected to the terminal

block. Connect the protect-

ive-earth conductor to the

corresponding terminal.

Note: A mains switch for ON

and OFF switching can of

course be installed in the

mains lead. This is a pre-

requisite for permanent light

function (refer to permanent

light function section,

page 15).

6. Apply the lampshade i

and secure by rotating.

7. Perform time, f light

threshold e and bright-

ness control g adjustment

(refer to functions section,

page 14).

Important: the safest motion

detection is obtained when

the device is mounted lateral-

ly to the walking direction and

no obstacles (such as trees

and walls, for example)

obstruct the view 1 .

mains power supply; this

work must therefore be

carried out professionally

in accordance with

regulations.

Dimensions (HxWxD): 315 x 315 x 135 mm

Output: ceiling mounting: 100 W max. / E 27

wall mounting: 60 W max. / E 27

Connection: 230 – 240 V, 50 Hz

Angle of coverage: 360° with 180° angle of aperture

Pivoting range: Fine adjustment ± 60°

Reach: max. 12 m (electronically stabilised)

Twilight setting: 2 – 2000 lux

Time setting: 5 sec. – 15 min.

Brightness control: 0 – 50 % (Watt-o-matic)

Permanent light: switchable (4 h max.)

Prerequisite:

connected switch in supply lead

Enclosure: IP 44

Temperature range: -20 °C to +50 °C

Installation instructions

Dear customer,

Congratulations on purchasing

your new STEINEL Ceiling-

SensorLight and thank you for

the confidence you have shown

in us. You have chosen a high-

quality product that has been

manufactured, tested and

packed with the greatest care.

Please familiarise yourself with

these instructions before

attempting to install the

CeilingSensorLight as

prolonged reliable and trouble-

free operation will only be

ensured if it is fitted correctly.

System components

a. Housing

b Sensor

c Lamp holder / E 27

d Decorative ring, removable

e Twilight setting

f Time setting

g Brightness control (dimming)

h Connection

i Glass with bayonet

Technical specifications

We hope your new Ceiling-

SensorLight will give you

lasting satisfaction.

1312

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel DL 750 S Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info