– 14 – – 15 –
Mounting
• Mark drill holes (Fig. 4.4)
• Drill holes and insert wall plugs - concealed
power supply cable (Fig. 4.5)
• Connect conductors (Fig. 4.6)
• Fit house number panel (L 630) to the light
enclosure (Fig. 4.7)
• Connect plug-in terminal, wall mount and light
enclosure (Fig. 4.8)
• Install light enclosure on wall mount (Fig. 4.9)
• Screw in retaining screws (Fig. 4.9)
• Switch ON power supply (Fig. 4.10)
• Make settings (Fig. 5.1)
➔ "5. F
5. Functions
Once installed, the sensor-switched light can be
put into oper
the sensor unit for selecting the time-, twilight- and
progr
F
Pr
T
Time setting (switch-OFF delay: 5s)
• Remove the sensor after pressing the locking tab
with a flat-tip screwdriver (Fig. 5.1)
The sensor-switched light switches t
override (permanently ON)
Progr
P1 Standard progr
Soft light start / no basic light level
What is soft light start?
The sensor-switched light featur
function. This means that when turned ON, the
light is not switched directly to maximum output
but constantly builds up brightness to 100
a short period of time. Brightness is also gradually
reduced when the light is switched OFF
P2 User-friendly pr
Soft light start + basic light level
Basic light level ON from twilight setting selected.
What is basic light level?
The basic light level provides continuous night-
time illumination at approx. 10
light only switches to maximum output (100
the time selected in response t
detection zone. The light then returns t
light level (approx. 10
Note: Depending on the local power grid, the LEDs
may flicker slightly when dimmed. This is not a
product defect and no reason for complaint.
Р
Soft light start + basic light level until the middle
of the night
Basic light level ON from twilight setting selected
until the middle of the night
What is the comfort economy programme?
The sensor-switched light does not have an int-
ed clock. The middle of the night is only determined
on the basis of the length of darkness phases.
T
sensor-switched light t
to the power supply during this period. During the
first night (calibration phase) basic light level r
activated throughout the night. The values ar
even in the event of a mains power failure. W
not recommend interrupting the power supply during
the progr
several nights, the sensor
the event of any fault occurring, be monitored over
several nights t
time moves towards midnight.
Р
Soft light start, no basic light level, no movement
evaluation
Switches on at 100
the level set
T
The chosen response threshold can be infinit
varied from appro
Control dial set to = daylight oper
(independent of ambient brightness)
Control dial set to = night-time oper
(approx. 2 lux)
T
the control dial must be set to (daylight
operation).
Time setting (5.1 H)
The light's ON time can be set to any period from
approx. 5s t
ment detected befor
the timer
Manual override function (Fig. 5.2)
If a mains switch is installed in the mains supply
lead, the following functions are available in addi-
tion to simply switching light ON and OFF:
8� Disposal
Electrical and electronic equipment, accessories
and packaging must be recycled in an envir
tally compatible manner
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current Eur
Electrical and Electronic Equipment and its imple-
mentation in national law
equipment no longer suitable for use must be coll-
ected separately and recycled in an envir
compatible manner
9. Manufacturer's warranty
This STEINEL pr
the utmost care, test
safety and then subjected to r
spection. Steinel guar
condition and proper working order
period is 36 months and starts on the date of sale
to the consumer
by material flaws or manufacturing faults. The war
ranty will be met by r
fective parts at our own discretion. The warr
shall not cover damage to wear parts, damage or
defects caused by improper treatment or maint
nance. F
objects shall be excluded.
Claims under the warranty will only be accept
if the unit is sent fully assembled and well-packed
with a brief description of the fault, a receipt or in-
voice (date of purchase and dealer's stamp) t
appropriate Service Centre.
Repair service:
If defects occur outside the warranty period or ar
not covered by the warr
vice station for the possibility of repair
MANUFACTURER'S
1
3
5
YEAR
GB
WARRANTY
MANUFACTURER'S
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
Sensor operation
1) Switch light ON (when light is OFF):
Switch OFF and ON once.
Light stays ON for the period selected.
2) Switch light OFF (when light is ON):
Switch OFF and ON once.
Light goes out or switches to sensor oper
Manual override
1) Activate manual override:
Switch OFF and ON twice. The light is set to stay
ON for 4 hours (red LED lights up behind the lens).
Then it returns automatically t
(red LED o
2) Deactivate manual override:
Switch OFF and ON once. Light goes out or
switches to sensor oper
Important:
The switch should be actuated in r
(in the 0.5 - 1s range).
Adjusting the detection zone (Fig. 5.3 to 5.8)
The detection zone can be limited t
ments. The shrouds supplied with the unit can be
used to mask out as many lens segments as you
wish. This prevents the light from being activat
unintentionally, e.g. by cars, passersby etc., and
allows you to target danger spots. The shr
be cut along the grooved vertical divisions. Then
you simply clip them onto the lens.
6. Other information
Example providing help on applying the house
number using the sheet of house numbers
included. (Fig. 6.1)
7. Operation / maintenance
The sensor-switched light is suitable for switching
light ON and OFF automatically
may aect the way the sensor-switched light func-
ti
cause the light to come ON when it is not wanted
because the sensor is unable to distinguish sudden
changes of temper
detector lens may be cleaned with a damp cloth if
it gets dirty (do not use cleaning agents).
GB
