Bedienungsanleitung Steinel L224 LED (Seite 6 von 55) (Alle Sprachen)

758034

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

– 10 – – 11 –

1. About this document

Please read carefully and keep in a safe place.

–Under copyright. Reproduction either in whole or

in part only with our consent.

–Subject to change in the interest of technical

progress.

Symbols

Hazard warning!

... Reference to other information in the

document.

2. General safety precautions

Disconnect the power supply before

attempting any work on the unit.

• During installation, the electric power cable to be

connected must not be live. Therefore, switch off

the power ﬁrst and use a voltage tester to make

sure the wiring is off-circuit.

• Installing these lights involves work on the mains

voltage supply; installation must therefore be

carried out professionally in accordance with

the applicable national wiring regulations and

electrical operating conditions (DE-VDE 0100,

AT-ÖVE/ÖNORM E 8001-1, CH-SEV 1000).

• Only use genuine replacement parts.

• Repairs may only be made by specialist work-

shops.

3. L 220 LED / L 224 LED

L 240 LED / L 244 LED

Proper use

–Sensor-switched outdoor light with LEDs as

the light source.

–Suitable for wall mounting outdoors.

The L 220 / L224 LED and L 240 / 244 LED

sensor-switched outdoor lights, referred to in the

following as lights, are active motion detectors.

Movement activates light. For your convenience,

safety and peace of mind. The integrated pyroelec-

tric infrared detector senses the invisible heat radi-

ated from moving objects (people, animals, etc.).

The heat detected in this way is converted

electronically into a signal that switches the light

on. Heat is not detected through obstacles, such

as walls or panes of glass, and will therefore not

activate the light.

Package contents L 240 LED / L 244 LED (Fig. 3.1)

Package contents L 220 LED / L 224 LED (Fig. 3.2)

Product dimensions L 240 LED / L 244 LED (Fig. 3.3)

Product dimensions L 220 LED / L 224 LED (Fig. 3.4)

Product components

L 240 LED / L 244 LED (Fig. 3.5)

L 220 LED / L 224 LED (Fig. 3.6)

A Light enclosure with base

B Plug-in terminal

C Wall mount

D Sensor

4. Installation

• Switch OFF power supply (Fig. 4.1)

The leads consist of three wires:

L = phase conductor (usually black,

brown or grey)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors

using a voltage tester; then disconnect from the

power supply again. Connect the phase conductor

(L) and neutral conductor (N) to the terminal block.

Important:

Incorrectly wired connections will produce a short

circuit later on in the product or your fuse box. In

this case, you must identify the individual conduc-

tors once again and re-connect them. A mains

power switch for turning the unit ON and OFF may

of course be installed in the mains supply lead.

Note:

The light source in this light must only replaced by

the manufacturer or a service engineer authorised

by the manufacturer or by a similarly qualiﬁed

person.

Connect the mains power supply lead (Fig. 5.6)

Wiring diagram (Fig. 4.2)

5. Mounting

• Check all components for damage.

• Do not use the product if it is damaged.

• Select an appropriate mounting location, giving

consideration to sensor reach and mounting

height (Fig. 5.1).

Mounting procedure

(Based on the example of L 220 LED)

• Switch OFF power supply (Fig. 4.1).

• Detach light housing from the wall mount, paying

attention to the position of the sensor (Fig. 5.2).

• Mark drill holes (Fig. 5.3).

• Drill holes and insert wall plugs (concealed power

supply cable (Fig. 5.4).

• Drill holes and insert wall plugs (with spacers for

surface power supply cable (Fig. 5.5).

• Connect conductors (Fig. 5.6).

• Connect plug-in connectors (Fig. 5.7).

• Fit light enclosure (A) onto wall mount (C). Pay

attention to plug-in connections as well as the

position of the sensor (Fig. 5.8).

• Screw light enclosure into place (Fig. 5.9).

• Switch ON power supply (Fig. 5.10).

• Make settings ➔ "6. Functions".

6. Functions

The sensor-switched light can be put into service

after mounting the light enclosure and connecting

to the mains power supply.

Factory settings

Twilight setting: daylight operation 2000 lux

Time setting: 8 s

Twilight setting / response threshold (Fig. 6.1)

–The sensor's response threshold can be inﬁnitely

varied from 2–2000 lux.

–Control dial set to = daylight operation,

approx. 2000 lux.

–Control dial set to = night-time operation,

approx. 2 lux.

Time setting (Fig. 6.1)

–Light ON duration can be inﬁnitely varied from

8 s - 35 min

–It is recommended that the shortest time be

selected for setting the detection zone.

–Control dial, shortest time = approx. 8 s

–Control dial, longest time = approx. 35 min

Adjusting the detection zone / reach setting

–Depending on the mounting height, the detection

zone setting can be optimised to suit require-

ments. The shroud foil can be used for masking

out any number of lens segments to limit reach

as required, e.g. to mask out paths or neigh-

bouring property (Fig. 6.2).

–Reach can be adjusted from 2-10 m by tilting

the sensor (D) through 90° (Fig. 6.3).

7. Disposal

Electrical and electronic equipment, accessories

and packaging must be recycled in an environmen-

tally compatible manner.

Do not dispose of electrical and electronic

equipment as domestic waste.

EU countries only:

Under the current European Directive on Waste

Electrical and Electronic Equipment and its imple-

mentation in national law, electrical and electronic

equipment no longer suitable for use must be

collected separately and recycled in an environ-

mentally compatible manner.

Steinel L224 LED Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info