Bedienungsanleitung Stiebel Eltron RTI-E3 (Seite 9 von 20) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

469639

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English

"CLICK"

X23

X21

X20

TA LE` LH LH` LE N

TALELHLHLENNNNNLL-SH

LNLE

L3 L2 L1

8/72

/40x

III

X15

X13

X12

X11

X10

X14

L3 L2 L1

X25

80 % PS

80 % NS

III

68/72 %

37/40 %

37/40

X15 X14

X13

TALELHLHLENNNNNLL-SH

LNLE

1 L3L2L1

80x PS

80x NS

68/72x AC

37/40x AC

III

8713.01

8715.01

8714.01

8716.01

⇒ Push the temperature selector button

(R2) into the operating panel and turn it

as far as the left-hand stop.

⇒ Rotate the shaft of the potentiometer as

far as the left-hand stop.

Engage the potentiometer into the opera-

ting panel from the switchbox side (check

that the potentiometer shaft is properly

located).

Lay the 3-pole connection lead of the po-

tentiometer along behind the angle plate

to the plug-in location of the discharge

control unit (in this situation, fix the con-

nection lead to the operating panel and

the angle plate by means of the cable

holder).

⇒ Pivot the angle plate located in the switch-

box forwards in order to accommodate

the mains connection terminals, after relea-

sing (not unscrewing) the screw located in

the rear wall.

⇒ Plug the connection lead (X25) on the di-

scharge control unit (A2) onto the charge

control unit (A1).

⇒ Guide the 6-pin plug connector of the di-

scharge control unit along behind the angle

plate and upwards, insert it form above

into the plug-in locations „TA“ to „N“ of

the connection terminal X2, and screw it

tight (push the cable harness into the cable

holder provided).

⇒ Plug the discharge control unit into the

longitudinal holes located above the charge

control unit and engage it in position.

⇒ Screw the room temperature sensor (B2)

with two screws (2.9 x 6.5) to the front

inclined edge of the baseplate. Plug the

connection cable into the plug-in location

X20 of the discharge control unit.

⇒ Plug the connection lead of the potentio-

meter into the plug-in location X21 of the

discharge control unit.

⇒ Guide the separate leads provided along

behind the angle plate and connect them

as shown in the following table (to the ter-

minals X1 and X2 from below):

from to

Lead (brown) LE`(X2) S2 (bottom

plug-in location)

Lead (black)

L (X1) S2 (top plug-

in location)

Designation Laying

The leads must not come in contact

with the operating panel conductor

plate or simply insulated leads for safety ex-

tra-low voltage (SELV).

Incorporate the leads to the S2 switch into

the existing cable harness (drillers can be

opened and then closed again).

⇒ Pivot the angle plate back to the rear again

and screw it tight.

⇒ Secure the side wall, front wall, and air out-

let and inlet grilles to the appliance once

again (respect the installation sequence).

The toothed disks must be inserted

beneath the securing screws of the

side wall and the front wall (protective con-

ductor connection).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron RTI-E3 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info