Bedienungsanleitung Stiebel Eltron RTI-E3 (Seite 10 von 20) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

469639

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

X25

X20

X21

X22

X23

L-

Aufladesteuerung

230 V-System

1/N/PE 230V

Aufladesteuerung

Kleinspannungs-System

LE` LH LH`

NNTA NN

3/N/PE 400 V

L3 L2 L1

L3 L2 L1213

X17

X13

X16

X11

X12

X14 - X15

X10

8699.02

The connection leads from the operating pa-

nel to the discharge control unit is to be laid

and secured in the same way as the existing

leads to the operating panel. They must not

come in contact with the intermediate wall or

the heating element connections.

2.2.2 Circuit diagram designations

X1 Mains connection terminal

X2 Connection terminal

Discharge control unit

A2 Electronic discharge control

B2 Room temperature sensor - discharge

R2 Adjuster - discharge

S2 ON/OFF switch, discharge control unit

X25 Internal connection strip A1-A2

2.2.3 Night time heating reduction

- connection of an external time-

clock

After installation, a switch or timeclock should

be wired to terminals L and TA on terminal

block X2. A temperature reduction of appro-

ximately 4 K can then be achieved.

The wiring for this modification must be pro-

vided by the installer, they are not included in

the kit.

2.3 Function test

Set the ON/OFF switch to the position " " .

Now rotate the temperature selector button

until the blower of the storage heater swit-

ches on. If the blower does not switch on, the

operating and fault displays on the charge and

discharge control units are to be observed.

2.3.1 Operating and fault display on

the electronic charging regulator

LED lights "green" ⇒ No fault

The charge control unit is working perfectly.

LED lights "red" ⇒ Fault

a) The selector button for charging (R1)

and/or the core sensor (B1) is defective

or not connected.

b) The plug bridge for reducing the degree

of charge at the discharge control unit is

missing.

No charging is taking place.

LED lights "orange" ⇒ Fault at the dischatge

control unit

a) Discharge control unit is defective.

b) Potentiometer for setting the discharge is

defective and/or not connected.

The room temperature will be regulated to

about 22 °C.

c) Room temperature sensor defective and/

or not connected.

No discharge is taking place.

2.4 Handover

These Operating and Installation Instructions

belong to the unit and are to be kept in a safe

4. Garantie

3. Environment and re-

cycling

Please help us to protect the environment by

disposing of the packaging in accordance with

the national regulations for waste processing.

For guarantee please refer to the respective

terms and conditions of supply for your coun-

try.

The installation, electrical connection

and ﬁ rst operation of this appliance

should be carried out by a qualiﬁ ed installer.

The company does not accept liability

for failure of any goods supplied which

are not installed in accordance with the

manufacturer's instructions.

place by the owner. In the event of change of

ownership, they are to be handed over to the

new owner. In the event of any maintenance

or repair work being necessary, the qualified

installer is to be provided with the Operating

and Installation Instructions in order to consult

them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron RTI-E3 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info