Bedienungsanleitung Stiga 740 WX - P 901 CH (Seite 158 von 588) (Alle Sprachen)

608664

158

Zoom out

Zoom in

Vorherige Seite

1/588

Nächste Seite

5.3.2 Battery charging

The battery must be fully charged befo-



Please refer to 9.10 for the battery char-

ging procedure.

5.4 SEAT

NOTE! To facilitate installation of the

seat, apply a drop of oil to the four

screws before screwing them in.

1. Remove the following components from the

seat bracket:

• 4 Nuts (for blocking during transport, not

used).

• 4 Screws.

• 4 Shoulder washers.

• Position the seat over the mounting in the

seat bracket.

1. Install the shoulder washers on the screws.

2. Insert the screws with the attached shoulder

washers through the slots in the seat bracket

and the holes in the seat plate. Screw the

seat into place.

Tightening torques 9±1.7 Nm

If the screws are tightened more than

9±1.7 Nm, the seat will be damaged.

1. Check that the seat moves easily in the slots

in the bracket.

The seat can be folded. If the machine is parked

outside where it is exposed to rain, tip the seat

forward to protect the seat cushion from getting

wet.

5.5 STEERING WHEEL (8)

In order to minimise axial play in the steering co-

lumn, place the 0.5-mm and/or 1-mm shim/s (3:C;

3:B) on the steering column between the sleeves,

pos. (8:A) as follows:

1. Install the sleeve (8:B) on the steering co-

lumn and secure in place by inserting one

of the pins (8:C) by approximately 1/3 of its

length.

2. Pull the sleeve and steering column upwards.

3. Check that the 0.5-mm shim, the 1.0-mm

shim (or both) can be inserted into the gap

which is created in point (8:A).. The shim/s

must not be forced in, as there must be a

little axial play.

4. Remove the pin (8:C) using a pin punch (8:D)

and remove the sleeve.

5. Install the shim/s as indicated in point 3

above.

6. Install the sleeve on the steering column and

secure by inserting both pins completely.

Block the steering column.

5.6 TOW BAR (9)

Install the tow bar (9:B) on the rear of the machine.

Use the screws and nuts (9:A; 9:C).

Tightening torque: 22 Nm.

5.7 QUICK-RELEASE SUPPORTS (1:N)

The quick-release supports and relative installa-

tion instructions are supplied in a separate box

inside the machine packaging.

Install the quick-release supports on the machi-

ne’s front axles.

5.8 TYRE PRESSURE

For the tyre pressure, please refer to chap. "0

TECHNICAL DATA TABLE".

5.9 ATTACHMENTS

For installation of attachment, see the installation

guide accompanying each attachment.

Note: In this case the cutting means as-

sembly is considered an attachment.

6 CONTROLS

6.1 MECHANICAL ATTACHMENT LIFT PE-

DAL (10:C)

The control lever (10:C1) is used to take the

accessories from the operating position to the

transport position.

• Transport position: press the pedal right down

then lift your foot o: the pedal stays down.

• Working position: press and slowly release the

pedal.

Do not attempt to switch to the tran-

sport position while the hooked-up

attachment is in operation. This will de-

stroy the drive belt.

6.2 PARKING BRAKE PEDAL (10:B)

Never press the pedal while driving.

There is a risk of overheating the power

transmission.

ENGLISH

(Translation of the Original Instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga 740 WX - P 901 CH Seite 158

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info