Bedienungsanleitung Stiga SE1814Q (Seite 26 von 357) (Alle Sprachen)

733496

Zoom out

Zoom in

Vorherige Seite

1/357

Nächste Seite

PACKAGING CONTENTS

The packaging contains:

– power unit,

– bar,

– chain,

– bar cover,

– bag containing equipment and documents.

The machine is supplied with

the bar and chain dismantled and the oil tank

empty.

Unpacking and complet-

ing the assembly should be done on a flat and

stable surface, with enough space for machi-

ne handling and its packaging, always making

use of suitable equipment.

Disposal of the packaging should be done in

accordance with the local regulations in force.

BAR AND CHAIN MOUNTING

Always wear heavy-duty

gloves when handling the bar and chain.

Mount the bar and chain very carefully so as

not to impair the safety and efficiency of the m-

achine. If in doubt, contact your dealer.

Before fitting the bar, make sure the chain brake is

not engaged; this is done by pulling the front hand

guard right back towards the body of the machine.

Make sure the machine is

not plugged into the mains socket.

• MACHINES WITH STANDARD

CHAIN TENSION ADJUSTER

– Remove the rubber protection (1a), unscrew the

nut (1) and remove the guard to get to the drive

sprocket and the point where the bar is fitted

(Fig. 1).

– Mount the chain in the right direction on the bar.

If the tip of the bar has a nose sprocket, make

sure the drive links are correctly inserted in the

sprocket rims (Fig. 2).

WARNING!

IMPORTANT

– Mount the bar (2) by inserting the stud bolt in the

groove and push it towards the back of the ma-

chine body and wind the chain around the drive

sprocket (Fig. 3).

– Check that the chain tension adjuster pin (3) is fit-

ted properly in the hole on the bar (Fig. 4); if it is-

n’t, turn the chain tension adjuster screw (4) us-

ing a screwdriver until the pin is completely

inserted (Fig. 5).

– Fit the guard back on without tightening the nut

(1).

– Turn the chain tension adjuster screw (4) to ad-

just the chain tension (Fig. 5).

– Raise the bar and tighten the guard nut (1) se-

curely using the supplied wrench, then replace

the rubber protection (1a) (Fig. 6).

• MACHINES WITH QUICK CHAIN TENSION

ADJUSTER

– Unscrew the handle (11) and remove the

guard to get to the drive sprocket and the point

where the bar is fitted (Fig. 1a).

– Mount the chain in the right direction on the bar.

If the tip of the bar has a nose sprocket, make

sure the drive links are correctly inserted in the

sprocket rims (Fig. 2).

– Mount the bar (2) by inserting the stud bolt in the

groove and push it towards the back of the ma-

chine body and wind the chain around the drive

sprocket (Fig. 3).

– Fit the guard back on without tightening the han-

dle (11). Check that the chain tension adjuster

pin (3) is fitted properly in the hole on the bar

(Fig. 4); if it isn’t, turn the chain tension adjuster

ring-nut (12) until the pin is completely inserted

(Fig. 5a).

– Turn the ring-nut (12) to obtain the desired chain

tension level (Fig. 5a).

– Raise the bar and tighten the handle (11) se-

curely (Fig. 6a).

6MACHINE ASSEMBLY

4. MACHINE ASSEMBLY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga SE1814Q Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info