Bedienungsanleitung Stiga SE1814Q (Seite 28 von 357) (Alle Sprachen)

733496

Zoom out

Zoom in

Vorherige Seite

1/357

Nächste Seite

8PREPARING TO WORK / STARTING - STOPPING THE ENGINE

3. Press the safety button (6) and then the switch

(7).

When you release the

switch, the safety button is also released and the

engine stops.

The chain may take one

second to come to a stop after the engine is

switched off.

STOPPING THE ENGINE

To stop the engine:

– Release the switch (7).

– FIRST unplug the extension lead (3) from the

mains socket (4) and THEN disconnect the

power cable (2) of the machine from the exten-

sion lead (3).

WARNING!

NOTE

STARTING THE ENGINE (Fig. 12)

Before starting the engine:

– Fasten the extension lead (1) to the cable clamp

on the rear handgrip.

– FIRST connect the power cable plug (2) to the

extension lead (3) and THEN plug the exten-

sion lead into the mains socket (4).

– Take off the bar cover.

– Make sure the bar is not touching the ground or

any other object

To start the engine (Fig. 12):

1. Disengage the chain brake (5) by pulling the

front hand guard towards the front handgrip.

2. Hold the chain-saw firmly with both hands.

6. HOW TO START - STOP THE ENGINE

Do not use the machine if

the chain brake does not function correctly

and have it inspected by your dealer.

4. CHAIN LUBRICANT

Only use chain-saw oil or ad-

hesive oil for chain-saws. Do not use oil containing

impurities, to avoid clogging the tank filter and per-

manently damaging the oiler.

The chain lubricating oil is

bio-degradable. The use of mineral oil or engine oil

can have a serious impact on the environment.

It is essential that you use good quality oil to lubri-

cate the cutting parts effectively.

Used or poor quality oil does not guarantee good

lubrication and reduces the duration of the chain

and bar.

Before each machine use,

the oil level should be checked and topped up to

1 cm from the rim of the filler. The oil level must not

drop below the «MIN» level mark.

5. ELECTRICAL CONNECTIONS

Electricity and moisture

are not compatible.

WARNING!

IMPORTANT

DANGER!

IMPORTANT

– Always handle and connect electric cables

in dry conditions.

– Keep electric sockets or cables away from

wet and damp areas (e.g. puddles or wet

ground).

The quality of the extension leads must be no less

than H07RN-F or H07VV-F, with a minimum sec-

tion of 1.5 mm2and a recommended maximum

length of 30 m.

To avoid overheating, do not keep the extension

lead rolled up during use.

The permanent connec-

tion of any electrical equipment to the mains of

a building must be installed by a qualified

electrician in conformity with the regulations in

force. Incorrect wiring can cause serious in-

jury and even death.

Supply power to the ma-

chine using a differential switch (RCD - Resid-

ual Current Device) with a tripping current of

max. 30 mA.

To prevent power supply

outages:

– make sure that the electric system’s overall ca-

pacity is adequate;

– connect the machine to a mains socket with suf-

ficient amperage;

– avoid simultaneous use of other electrical appli-

ances with high power consumption.

IMPORTANT

DANGER!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga SE1814Q Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info