Bedienungsanleitung Stiga SP 375Q (Seite 36 von 460) (Alle Sprachen)

608366

Zoom out

Zoom in

Vorherige Seite

1/460

Nächste Seite

Never start the chain saw

by holding on to the starter cable and allowing

it to fall. This is an extremely dangerous

method as you lose complete control over the

machine and the chain.

To avoid breaking the starter

rope, do not pull the whole length of it or let it slide

along the edge of the cable guide hole. Release the

starter gradually, to avoid letting it fly back uncon-

trollably.

7. Push the choke knob inward halfway.

8. Pull the starter rope again until the engine starts

as normal

If the starter rope is pulled

repeatedly with the choke on, it may flood the en-

gine and make starting difficult. If you have flooded

the engine, remove the spark plug and gently pull

the handle on the starter rope to eliminate any ex-

cess fuel; then dry the spark plug electrodes and

replace it on the engine.

9. When the engine has started, press the throttle

trigger to disconnect the starter and allow the

engine to idle.

Do not let the engine run at

high power with the chain brake engaged, as this

could cause overheating and damage to the clutch.

10. Pull up the front handle guard toward the front

handle to release brake.

Let the engine run idle for at least 1 minute be-

fore using the machine.

• Hot starting

When hot starting (immediately after stopping the

engine), follow the procedure indicated above in

points 1 - 2 - 5 - 6 - 9 - 10.

USE OF THE ENGINE (Fig. 10)

Always disengage the chain

brake, pulling the lever towards you before using

the accelerator.

IMPORTANT

DANGER!

IMPORTANT

NOTE

IMPORTANT

STARTING THE ENGINE

The engine must be start-

ed in an area at least 3 metres from where

you refilled the fuel tank.

Before starting the engine:

– Place the machine firmly on the ground.

– Take off the bar cover.

– Make sure the bar is not touching the ground or

any other object.

– Before you start the engine, make sure the saw

chain is not contacting anything. Make sure the

chain brake always is activated before each

starting.

• Cold starting

A “cold” start of the engine

means starting it after at least 5 minutes from when

it was switched off or after refuelling.

To start the engine (Fig. 8):

1. Check that the chain brake is engaged (with

the front hand guard pushed forward).

2. Set the switch (1) to «START».

3. Pull the knob (2) as far as possible to engage

the starter.

4. Press the primer device button (3) 3 or 4 times

to prime the carburettor.

5. Hold the machine firmly on the ground, with

your hand on the handgrip and your foot in the

rear handgrip, to avoid losing control during

starting (Fig. 9).

If the machine is not held

firmly, the force of the engine could cause the

user to lose his balance or direct the bar to-

wards him or an obstacle.

6. Pull the starter rope slowly for 10 - 15 cm until

you feel some resistance, then tug it hard a few

times until you hear the engine turn over.

Never wind the starter ca-

ble around your hand.

WARNING!

NOTE

WARNING!

10 HOW TO START - USE – STOP THE ENGINE

6. HOW TO START - USE – STOP THE ENGINE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga SP 375Q Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info