Bedienungsanleitung Stiga TORNADO 2198 H (Seite 68 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

608471

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Hydrostatic transmission

Drive down slopes with your foot o the drive

pedal (see 4.32) to use the braking eect of

the hydrostatic transmission when the trans-

mission is not engaged.

5.6 SUGGESTIONS FOR MAINTAINING A

NICE LAWN

1. To keep a lawn green and soft with a good

appearance, it should be cut regularly with-

out damaging the grass. A lawn can be com-

posed of dierent types of grass. If the lawn

is cut frequently, grass and roots grow more

vigorously, forming a solid grassy bed. If the

lawn is cut is less frequently, higher grass

and weeds start growing (clover and daisies,

etc.).

2. It is always better to cut the grass when dry.

3. The cutting means must be in good condition

and well sharpened so that the grass is cut

straight without a ragged edge that leads to

yellowing at the ends.

4. The engine must run at full speed, both to

ensure a sharp cut of the grass and to get the

necessary thrust to push the cuttings through

the collector channel.

5. The frequency of mowing should be in rela-

tion to the rate of growth of the grass, which

should not be left to grow too much between

one cut and the next.

6. During hot and dry periods, the grass should

be cut a little higher to prevent the ground

from drying out.

7. The best height of the grass on a well-kept

lawn is approx. 4-5 cm. and with one mowing,

you do not need to remove more than a third

of the total height. If the grass is very tall,

it should be cut twice in a twenty-four hour

period. The rst time with the cutting means

at maximum cutting height, possibly reducing

the cutting width and the second cut at the

height desired. Fig. 5.13)

8. The appearance of the lawn will improve if

you alternate the cutting in both directions

(Fig. 5.14)

9. If the collector system tends to get blocked

with grass, you should reduce the forward

speed as it may be too high for the condi-

tion of the grass. If the problem persists, the

probable causes are either badly sharpened

cutting means or deformed ns.

10. Be very careful when mowing near bushes

or kerbs as these could distort the horizon-

tal position of the cutting-means assembly

and damage its edge as well as the cutting

means.

6. MAINTENANCE

6.1 SAFETY RECOMMENDATIONS

WARNING! You must go to a special-

ized Service Centre or contact your Dealer if

the following are malfunctioning:

– the brake;

– the cutting means engage and disengage

functions,

– switching the drive to forward or reverse

gears.

6.2 ROUTINE MAINTENANCE

The table will help you maintain your machine’s

safety and performance. It summarises the main

interventions to be made and the frequency ap-

plicable to each of them.

The boxes at the side are for you to mark the

date or number of working hours at which the

intervention was made.

Operation

Hours

Completed (Date or Hours)

1. MACHINE

1.1

Cutting means positioning and sharpening

check

1.2

Replacing cutting means

100

1.3

Transmission belt check

1.4

Transmission belt replacement

2) 3)

–

1.5

Cutting means control belt check

1.6

Replacing the cutting means control belt

check

2) 3)

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga TORNADO 2198 H Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info