Bedienungsanleitung Stiga TORNADO 2198 H (Seite 70 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

608471

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

IMPORTANT This connector must only be

used for connection to the maintenance battery-

charger indicated by the Manufacturer. For its

use:

– follow the instructions given in the relative in-

structions manual;

– follow the instructions in the battery manual.

6.3 INTERVENTIONS ON THE MACHINE

6.3.1 Aligning the cutting-means

assembly (Fig. 6.3)

The cutting-means assembly should be prop-

erly adjusted to obtain an evenly mown lawn.

If mowing is uneven, check the tyre pressure.

If this is not sucient to achieve an even cut,

please contact your Dealer to adjust the align-

ment of the cutting-means assembly.

6.3.2 Replacing the wheels (Fig. 6.4)

Stop the machine on at ground and put a block

under a load-bearing part of the frame on the

side that the wheel is to be changed.

The wheels are held by a snap ring (1) which

can be removed with a screwdriver.

NOTE If you have to replace one or both rear

wheels, make sure that any differences in their

external diameter does not exceed 8-10 mm; on

the contrary, you must adjust the cutting-means

assembly alignment to prevent uneven mowing.

IMPORTANT Before remounting the wheel,

apply grease to the axle. Put the snap ring (1)

and shoulder washer (2) back in place.

6.3.3 Repairing or replacing tyres

The tyres are “Tubeless” and must be replaced

or repaired if punctured by a specialized tyre

repairer following the procedures required for

this kind of tyre.

6.3.4 Replacing bulbs ( if tted)

• Type “I” bulbs (incandescent) (Fig. 6.5)

The bulbs (18W) have a bayonet tting and are

installed in the bulb holder which can be taken

out by turning it anti-clockwise with pliers.

• Type “II” bulbs (LED) Fig. 6.6)

Unscrew the ring-nut (1) and remove the con-

nector (2).

Remove the LED illuminator (3), secured by

screws (4).

6.3.5 Replacing a fuse (Fig. 6.7)

The machine is tted with fuses (1) with dierent

capacities and functions. Specically:

– 10 A fuse = protects the main and power cir-

cuits of the electronic circuit board. When it

blows, the machine stops.

– 25 A fuse = protects the battery recharge cir-

cuit. When it blows, the battery gradually runs

down and the machine will have problems

starting.

The fuse capacity is indicated on the fuse.

IMPORTANT A blown fuse must always be

replaced by one of the same type and ampere

rating, and never with one of another rating.

If you are unable to understand why it has

blown, contact Your Dealer.

6.3.6 R emoving, replacing and

reassembling of cutting means

WARNING! Always wear strong protec-

tive gloves to handle the cutting means.

WARNING! Always replace damaged or

bent cutting means; never attempt to repair

them! ALWAYS USE ORIGINAL CUTTING

MEANS!

Only cutting means bearing the code indicated

in the table on page ii must be used on this ma-

chine.

Given product evolution, the above mentioned

cutting means may be replaced in time with oth-

ers having similar interchangeable and operat-

ing safety features.

IMPORTANT Cutting means should be

replaced in pairs, especially when there are

marked differences in wear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga TORNADO 2198 H Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info