Bedienungsanleitung Stihl FS 460 C-M K (Seite 15 von 116) (Englisch, Spanisch)

537264

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

FS 460 C-M, FS 460 C-M L, FS 490 C-M, FS 490 C-M L

English

WARNING

USING THE CUTTING ATTACHMENT

For an illustration of the various cutting

attachments and instructions on proper

mounting see the chapter on "Mounting

the Cutting Attachment" in your

instruction manual.

WARNING

To reduce the risk of severe or fatal

injury from blade contact and / or loss of

control, never attempt to use a metal

blade on an FS model for which it is not

authorized.

Using the Mowing Heads

Do not use with mowing line longer than

the intended length. With a properly

mounted deflector, the built-in line-

limiting blade will automatically adjust

the line to its proper length.

Using the unit with an overly long nylon

cutting line increases the load on the

engine and reduces its operating speed.

This causes the clutch to slip

continuously and results in overheating

and damage to important components

(e.g. clutch, polymer housing

components). Such damage could,

among other things, cause the cutting

attachment to rotate at idle.

Mowing heads are to be used only on

clearing saws equipped with a line-

limiting blade in the deflector in order to

keep the line at the proper length (see

"Main Parts" chapter in your instruction

manual).

If the lawn edges are planted with trees

or bordered by a fence etc., it is best to

use a nylon line head. It achieves a

"softer" cut with less risk of damaging

tree bark etc. than polymer blades.

However, the polymer-bladed STIHL

PolyCut produces a better cut if there

are no plants along the edge of the lawn.

Sharpening is not necessary, and worn

polymer blades are easily replaced.

WARNING

To reduce the risk of serious injury,

never use wire or metal-reinforced line

or other material in place of the nylon

cutting lines. Pieces of wire could break

off and be thrown at high speed toward

the operator or bystanders.

STIHL SuperCut mowing head

Fresh line is advanced automatically.

Frayed line is replaced by a simple

adjustment (see instruction sheet

supplied with mowing head).

STIHL AutoCut mowing head

Nylon cutting line advances

automatically when tapped against the

ground (TapAction).

STIHL TrimCut mowing head

Frayed line is replaced by a simple

adjustment (see instruction sheet

supplied with mowing head).

STIHL DuroCut mowing head

Uses only nylon lines.

Observe wear indicators.

NOTICE

There are four wear limit indicators

shaped like exclamation marks in the

base of the DuroCut. If one of these

Some STIHL power tools

are equipped with a cata-

lytic converter, which is

designed to reduce the

exhaust emissions of the

engine by a chemical pro-

cess in the muffler. Due

to this process, the muf-

fler does not cool down

as rapidly as conven-

tional mufflers when the

engine returns to idle or

is shut off. To reduce the

risk of fire and burn inju-

ries when using a

catalytic converter,

always set your power

tool down in the upright

position and never locate

it where the muffler is

near dry brush, grass,

wood chips or other com-

bustible materials while it

is still hot.

002BA354 KN

681BA209 KN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl FS 460 C-M K Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stihl FS 460 C-M K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info