555292

Stomer SMS-1800-T Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
11
MITRE SAWING (FIG 5)
During mitre sawing, the workpiece is sawed at an angle in
relation to the mitre and width guide.
● Starting position:
– Saw head completely raised.
– The motor head stands in a vertical position (90°), and
the bevelling lock knob is tightened.
● Sawing the workpiece:
– Release the mitre locking knob.
– Set the desired angle.
– Tighten the mitre locking knob once more.
– Hold the workpiece against the mitre and width guide.
If necessary, use a work clamp for fastening the
workpiece.
– Activate the switch and activate/push on the safety lock.
– Lower the saw head carefully and completely downwards
while holding fi rmly onto the handgrip. You should only
apply medium pressure while sawing, so as to prevent
that the speed of the motor slows down.
– Saw the workpiece in one single movement.
– Carefully let the saw head return to its topmost starting
position.
– The saw should be switched off by releasing the switch,
if no further sawing has to be done.
Note: The mitre saw is activated at certain angles,
such as at 0°, 15°, 22.5°, 30°, 45°.
BEVELLING (FIG 6)
During bevelling, the workpiece is sawn at an angle of less
than 90°.
● Starting position:
– Saw head completely raised.
– Motor head in the 0° position; the locking screw of the
turntable is tightened.
SAWING THE WORKPIECE:
● Release the bevelling locking knob for tilting the saw
head close to the saw.
● Tilt the motor head carefully to the desired position.
● Tighten up the bevelling lock knob.
● Hold the workpiece against the mitre and width guide. If
necessary, use a work clamp for fastening the workpiece.
(20)
● Activate the switch and activate/push on the safety lock.
● Lower the saw head carefully and completely downwards,
while fi rmly holding onto the handgrip. You should only
apply medium pressure while sawing, so as to prevent
that the speed of the motor slows down.
● Saw the workpiece in one single movement.
● Carefully let the saw head return to its topmost starting
position.
● The saw should be switched off by releasing the switch,
if no further sawing has to be done.
DOUBLE MITRE CUT
A double mitre cut is a combination of a mitre cut and a
bevelling cut; this means that the workpiece is cut at an
angle in the one single movement, which is not equal to
90° in relation to the mitre and width guide and the material
surface.
INSTALLATION
HAZARD!
Before starting with the installation of the machine:
– Switch the machine “OFF”
– Remove the plug from the socket
– Wait until at the machine has come to a complete
standstill
● Release the locking knob and lift up the saw head
completely
● Remove the lower saw blade guard.
● Use the switch for activating the machine.
HAZARD!
● Before using the machine, always check that the following
items function properly.
– Movable saw blade guard.
● Wear protective clothing
● Stand in the correct position for operating the machine
– At the front of the saw
– In front of the saw
– To the side of the sawing line
● Crushing hazard! Whenever you tip the sawing head to
the side, you must have a fi rm grip on the handle of the
saw head, keep your fi ngers away from the support arm
and out of the tilting range! Hold the saw head fi rmly.
● If required by the type of work you are doing, you must
use the following accessories:
– Workpiece support for long workpieces, which would
otherwise fall off the table at the end of the sawing
process.
– Dust collector
● Use an additional guide, if small pieces have to be
sawn.
● Always hold of the workpiece fi rmly on the table and do
not block it.
● Do not try to stop the turning of the saw blade, by pressing
the workpiece against the edge of the saw blade. A risk of
injuries can occur, if the saw blade is blocked.
NORMAL CROSS-CUT OPERATIONS (FIG 4)
● Starting position:
– Saw head completely raised.
– Turntable in the 0° position; the locking screw of the
turntable is tightened.
– The motor head stands in a vertical position (90°), and
the bevelling lock knob is tightened.
● Sawing the workpiece:
– Hold the workpiece against the mitre and width guide;
if possible use a work clamp for fastening down the
workpiece.
– Activate the switch and activate/push on the safety lock.
– Lower the saw head carefully and completely downwards
while gripping the handgrip. To prevent that the speed of
the motor slows down, you should only apply medium
pressure while sawing.
– Saw the workpiece in one single movement.
– Carefully let the saw head return to its topmost starting
position.
– The saw should be switched off by releasing the switch,
if no further sawing has to be done.
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stomer SMS-1800-T wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info