Bedienungsanleitung Stomer SMS-1800-T (Seite 10 von 28) (Englisch)

555292

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

● When sawing oak-, beech- or ashwood.

● The dust collector must conform to the following

requirements:

● The diameter of the dust exhaust pipe must ﬁ t properly

(34 mm);

● The air ﬂ ow volume must exceed 550 m³/h;

● The vacuum at the dust exhaust exit must be ≥ 740 Pa;

● The air speed at the dust exhaust exit must be ≥ 20 m/s;

● Follow the user instructions for the dust collector.

CONNECTION TO AC POWER

High-voltage!

● Only operate this machine in dry surroundings.

● This machine may only be connected to a power source

that fulﬁ ls the following requirements (also see the

section "Technical data"):

– The mains voltage and the system frequency must

conform to the voltage and frequency that is indicated on

the technical data sheet of the machine;

– Fusing protection with a residual current device (RCD),

with a sensitivity of 30 mA.

– Sockets must be properly installed, earthed and tested.

– Position a power cable in such a way that it does not

hinder the work and cannot be damaged.

● Protect the power cable against heat, aggressive ﬂ uids

and sharp edges.

● Only use rubber-coated extension cables with a sufﬁ cient

wire cross-section (3 x 1.5 mm²).

● Do not use the power cable for pulling the plug out of the

socket.

OPERATIONS

This saw can be used as a:

● Cross-cut saw

● Table saw

Before making any changes in the settings of this

machine, always remove the plug from the

socket.

CROSS-CUT SAWING MODE

SAFETY INSTRUCTIONS FOR THE MOVABLE

SAW BLADE GUARD (FIG 2)

The movable saw blade guard protects against accidental

contact with the saw blade and ﬂ ying wood splinters.

The movable saw blade guard must always return

automatically to the start position, whenever the saw head

is lifted. The saw blade must be covered at all sides, when

the saw head is located in the start position.

SAFETY LOCK (FIG 3)

The safety lock blocks the saw head in the topmost position,

and it prevents that the movable saw blade guard exposes

the saw blade.

The safety lock is released by pushing on it. The saw head

can now be lowered; as the saw head is lowered, the saw

blade guard retracts and the saw blade is freed.

After a cut has been made, and when the saw head is back

in the topmost starting position, the movable saw blade

guard is once more blocked by the safety lock.

TRANSPORT

● Position the lowest saw blade guard over the saw guide

piece and push backwards until you hear a click, and until

he saw blade protector is positioned at the black line on

the saw guide piece.

● Lower the saw head by pushing in the safety lock and

activate the locking pin.

● Lift the machine up by grasping both sides of the base.

Note: The essential operating components of the

machine are presented in this section. Make sure

to read this section, before you use the machine

for the ﬁ rst time.

TABLE SAW OPERATING MODE

● Make sure that the table is mounted completely and in

the right direction – and that the locking pin is properly

locked.

● Release the table stops, so that you can push down the

table. Then lock with stops. (8&9)

● The ON/OFF switch is used for starting and stopping the

machine. (1&2)

CROSS-CUT AND MITRE SAW OPERATING

MODE

● Release the table stops so that the table can be pushed

up by springs. After that lock with

the stop.

● Remove the lower saw blade guard. (41)

● For starting the motor, push on the switch in the handgrip.

(13)

● To switch off the motor, release the switch.

TURNTABLE (16)

The turntable can be turned 49° to the left and 49° to the

right, and it can be ﬁ xed in preset positions of 0°, 15°, 22.5°,

30°, 45°.

For turning the mitre table, the locking knob must be

released.

To prevent that the mitre angle changes while sawing, the

locking knob of the mitre saw must be tightened (also when

the saw has been ﬁ xed at a preset stop).

ADJUSTMENT OF THE BEVELLING ANGLE

The support arm can be tilted vertically and in an angle of

45° to the left.

To be able to tilt the support arm, the bevel lock must be

released.

To prevent the bevel angle from changing while sawing, the

locking knob of the support arm must be tightened.

MITRE AND WIDTH GUIDE

The mitre and width guide is mounted on the top saw table.

The mitre and width guide locking knob must point towards

the front of the machine. Once the locking knob is released,

the mitre and width guide can be removed.

CONNECTION TO A DUST COLLECTOR

The dust of some types of wood (such as for instance

beech, oak and ash) can be hazardous if inhaled. Always

use a dust collector:

● If the saw is set up in an enclosed space;

● Whenever the saw is being used for longer periods of

time (more than a half hour per day);

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SMS-1800-T Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info