Bedienungsanleitung Stovax Studio (Seite 6 von 36) (Englisch, Französisch, Italienisch)

813436

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

FUEL OVERLOADING

The maximum amount of fuel specified in this manual should not be

exceeded, overloading can cause excess smoke.

CHOOSING FUEL:

All types of wood can be used as fuel in the appliance. Different

types of wood have different densities: the greater the density of

the wood the greater the energy value.

Oak, beech and birch have the highest value.

The correct moisture content for firewood that is ready to burn is

below 20% moisture content.

If wood is too wet, it will be difficult to light, struggle to burn, give

very little heat output and tar up the flue.

This could lead to a chimney fire, so it is important to burn

sufficiently dried firewood.

Dry wood gives more heat output, avoids blackening the appliance

glass and there is minimal soot build up in the chimney or flue.

More heat output equals less fuel.

Do not burn construction timber, painted,

impregnated / treated wood, manufactured board

products or pallet wood.

Wood Storage:

To ensure thoroughly dry wood, cut in winter and store under a roof

with plenty off room for air circulation.

Do not cover completely, leave a gap for air to pass over the wood

and do not seal.

Bring wood intended for use inside and store for a few days

prior to burning to ensure that the moisture has been sufficiently

decreased.

ASH REMOVAL

Wood burns best on a bed of ash

Do not allow ash to build up in the appliance as it will not burn

properly and may cause damage.

Remove ash with a small shovel (available from Stovax). Take care

not to damage the ceramic lining of the appliance.

Do not use sharp pointed pokers.

Remove ash carefully - heat can remain long after use.

Carefully place the ash into a Stovax Ash Caddy.

Do not place hot ash in a container made from plastic or any

other combustible material.

OVER-FIRING

Do not over-fill with fuel or run at high temperatures for long periods

or over-firing can occur.

DO NOT OPERATE THE APPLIANCE WITH THE PRIMARY

AIR CONTROL OPEN FOR LONG PERIODS OF TIME AS THIS

COULD CAUSE OVER-FIRING AND MAY CAUSE PERMANENT

DAMAGE.

Over-firing can cause permanent damage to the appliance and

invalid the product warranty.

CHIMNEY FIRE

If a chimney fire occurs:

— Shut all air controls immediately.

— Evacuate the building.

— Call the fire brigade.

— Do not re-enter the building until it is confirmed safe.

Do not use the appliance after a chimney fire until:

a) It has been inspected by a registered installer, confirming

the appliance is safe to use.

b) The chimney system has been inspected and swept by a

chimney sweep, confirming the system is structurally sound and

free from obstruction*.

c) It is repaired as required before re-use. Use only genuine

Stovax replacement parts to keep your appliance in safe, efficient

working order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax Studio Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stovax Studio

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info