Bedienungsanleitung Stovax View 7 Inset High Output Boiler Inset (Seite 24 von 44) (Englisch)

813428

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation Instructions

Connecting the Flue

The flue must be installed in accordance with the

manufacturers instructions.

1.17 Fill the void at the back of the box with 6:1 vermiculite/cement

mix or any other good non-combustible insulation material. It

is important to insulate the back, top and side of the box.

CHECK THE BOILER CONNECTIONS FOR

ANY SIGN OF LEAKS BEFORE ANY INFILLING

REQUIRED IN THE INSTALLATION.

1.18 Insert the flue spigot from inside the appliance.

1.19 Connect the flue liner to the flue collar using the flue liner

adaptor.

1.20 Seal liner and adaptor with fire cement.

1.21 If the appliance is installed on an unlined, masonry flue:

— Fit a non-combustible closure plate to locate the first section

of single wall flue pipe from the appliance to the old system.

— Make the connection as with a flue liner system.

1.22 Do not connect the system into large voids that could

exist in older chimney systems. If this is the case consider

using a flue lining system to improve the operation of the

appliance, see Diagram 3.

Closure Plate

Ridged Flue

Pipe

Flue Liner

Adaptor

Supplied By

Flue Liner

Manufacturer

2. Steel Top & Optional Glass Top

The appliance is supplied with a flat steel top.

2.1 Place the top on the appliance ensuring it is central and

flush with the sides of the appliance. The front of the top

should line up with the door. The top also has 3 x threaded

bosses on the underside, see Diagram 4. Ensure the 2 x

front bosses line up with the holes in the carcass top.

2.2 With the door open, fix the steel top in position from the

underside using the 2 x M8 x 20 hex head screws and 2 x

M8 crinkle washers.

Washer

Screw

2.3 This appliance can also be fitted with an optional glass top

(part no. VW-7NGB). The top has 5 x silicon feet on the

bottom to space it off the steel top.

2.4 Place the glass top, feet down, on the appliance. Ensure the

glass top is flush with the front and sides of the steel top.

3. CO Alarms

All open flued appliances can be affected by temporary

atmospheric conditions which may allow fumes to enter

the house. Building regulations require that whenever

a new or replacement fixed solid fuel or wood/biomass

appliance is installed in a dwelling a carbon monoxide

alarm must be fitted in the same room as the appliance.

Further guidance on the installation of the carbon

monoxide alarm is available in the latest edition of

BS EN50292 and from the alarm manufacturer's

instructions.

HETAS recommend the unit is permanently fixed

in accordance with the manufacturer's installation

instructions or with the guidance contained in Approved

Document J where no other information is available.

Provision of an alarm must not be considered a

substitute for either installing the appliance correctly

or ensuring regular servicing and maintenance of the

appliance and chimney system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax View 7 Inset High Output Boiler Inset Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info