Bedienungsanleitung Strong srt 6004 (Seite 11 von 23) (Englisch)

424658

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PART 1 • English

Connecting a dish on a motorized positioner to your receiver (Fig. 9)

Another possibility for watching programs from multiple satellites is by mounting a dish to a

motorized DiSEqC 1.2 positioner. Have your dealer mount the dish to the positioner, set the correct

angle of the elevation and let him set the center point for your positioner. Connect the LNB with

a coax cable to the LNB IN connector of the positioner, and connect the OUT connector of the

positioner to the LNB IN connector at the back of your receiver.

3.4 Connecting to serial cable for downloading software

Connect the RS-232 connector on the back of your receiver to the Serial port of your computer

using a serial cable. Instructions how to download software can be found on our website www.

strongsat.com (support > download). However, this receiver can download new system software

automatically by satellite. (Fig. 10)

4.0 STARTING UP

Ensure your satellite receiver is correctly connected to your television and dish, and that your

satellite signal is of good quality. (If you are not sure about this then ask your local strong dealer to

check your installation or satellite signal.) Conﬁrm that the power plug on the receiver is plugged

into the wall outlet. Turn on the receiver. It is recommended that you perform the ﬁrst time

installation following the Installation Wizard step by step. It will help you to easily achieve system

conﬁguration and channel installation. If you are a professional installer then you can skip wizard by

pressing MENU button and set-up channels using the Installation menu.

4.1 Language Selection

Press UP/DOWN to choose your language, press OK to conﬁrm. The Select Satellite menu will

appear. Future installation steps are depending from satellite where your dish is aimed.

4.2 Select Satellite

a) Your dish is aimed to Astra 1C, 1E, 1F or Hotbird satellite.

Press UP/DOWN to select the ASTRA or Hotbird satellite and press OK button. Follow the

instructions. When you have ﬁxed your dish at correct direction choose

NEXT and press the OK

button. The Channel Setup menu will appear.

b) Your dish is aimed at another satellite

Select Other in Select satellite menu and press OK, more satellites will be listed. If you select one out

of the satellite list, the Conﬁgure Antenna menu will appear, please set the LNB Type, LNB Low Freq,

LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode.

4.3 Antenna mode

a) Fixed dish

Set Antenna mode to Fixed, select NEXT and press the OK button. The Adjust antenna screen appears,

select transponder receivable at your location and adjust the antenna position for maximum level for

the signal strength and quality. When you have completed the adjustment, choose NEXT and press

the OK button. The Channel Setup menu will appear

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong srt 6004 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong srt 6004

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info