Bedienungsanleitung Strong SRT 7000 (Seite 15 von 25) (Englisch)

480531

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

PART 1 • English

7.3 Channel Search

To access the menu press MENU and select Channel Search. It contains two options: Installation and DB

(Data Base) Management. Select an option and press OK to enter it. Press EXIT to exit the menu.

7.3.1 Installation

7.3.1.1 Satellite Selection

Use pqbuttons to highlight the satellite your dish is aimed at. Its antenna settings will be shown at the

right side. You can enter the right side with tu buttons and return to the satellite list with EXIT.

7.3.1.2 Conﬁgure the antenna settings for selected satellite

LNB Type: Press tu or OK to show the list of LNB Types which is shown as frequencies

of local oscillator. You also can enter frequency by User Single, User Dual at

bottom of the list. Default is set a Universal LNB (09750/10600) – the most

used on the market.

LNB Power: Press tu to set the LNB power. 13/18V is the setting for a Universal LNB.

22 kHz: Press tu to switch on or off the 22KHz oscillator signal. Auto is the setting for

a Universal LNB.

Toneburst: to enable or disable the toneburst switcher if available.

DiSEqC1.0: to select the right port from up to 4 (if available) for the right LNB.

DiSEqC1.1: to select the right port from up to 16 (if available) for the right LNB.

Motor: if using a motor press tu to select between DiSEqC1.2 or GOTOX depending

of motor type. Then Press OK to show the menu to set position or GREEN

for location.

DiSEqC1.2: Move the motor to the right position for locking the signal like explained below.

Move Continue: Press tu for moving West / East. It will keep moving as long as the button is

hold pressed. Once pressing will move in 1°step.

Move Step(1): Press tu for moving West / East in 0.3° step.

Store Position: to store the current motor position for selected satellite.

Goto Reference: to go to the reference 0° position.

GOTO X: Set your location coordinates. Main German locations are preinstalled. Press

tu to select. If Manual selected use tu, UP/DOWN and NUMERIC buttons

to enter the right position. By pressing OK position gets stored and the motor

moves automatically towards selected satellite.

Set Limit for DiSEqC1.2 and GOTO X options:

For Move Continue, Move Step(1) and Goto Reference please see explanation above.

Set West Limit: to store the current motor position as West limit.

Set East Limit: to store the current motor position as East limit.

Disable Limit: to disable West and East limits

7.3.1.3 Channel Scan

Automatic Scan

Single Satellite Scan: Press BLUE for Scan. A window with scanning settings will be displayed.

Scan Mode: Press tu to select Default, Blind Scan or NetWork.

Default: All in the memory stored transponders will be scanned.

Blind Scan: Slow scan in 2 MHz step. It ﬁrst scans the whole frequency band to get the

transponders which can be locked. After gathering all transponders, it scans

the transponders one by one to get the programs.

NetWork: Network search will be performed – when a Network information is

broadcasted new switched transponders will be found and stored.

Crypted: Press tu to select All Channels (scrambled and free) or FTA Channels (free to air);

Service Type: Press tu to select ALL, DTV or Radio.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info