Bedienungsanleitung Strong SRT 7300 CI plus (Seite 14 von 23) (Englisch)

568532

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PART 1 • English

English

Note: Press YELLOW in the Manual Scan menu to make settings for a PID search.

Scan mode, Service type and Network search will then be replaced by settings for

Video PID, Audio PID and PCR PID. For information on PID values, please visit

websites like: www.lyngsat.com or www.kingofsat.net

7.1.4 Satellite Edit

Here you can edit transponder data or add a new satellite.

On the left of the screen, a list with all available satellites is displayed. The right of the screen displays a

list will all available transponders for the highlighted satellite.

Adding or editing a transponder

Use pq to highlight the desired satellite. Press u to move the highlight to the transponder list. Press

YELLOW to add a transponder or use pq to highlight the transponder to be edited and then press

BLUE to enter the edit screen. Use pq to navigate in the edit screen and use tu respectively [0~9] to

change the settings. Once all settings are made, press GREEN to save or EXIT to quit without saving.

Editing an existing satellite

Use pq to highlight the satellite you wish to edit. Press BLUE to go to the Satellite Edit screen. To edit

the name of the satellite, use pq to highlight the name and press OK. A keyboard will pop up. Use pq

tu to navigate and OK to input the chosen character. Once ﬁnished press GREEN to save the changes

or EXIT to quit without saving. To edit the position of the satellite, use pq to move the highlight

to Position and use the [0~9] buttons to input the new position. To change the location, use pq to

highlight Location and use tu to change the location. Possible settings are: East and West. Once all

settings are made press GREEN to save or EXIT to quit without saving.

Adding a satellite

To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and

press YELLOW. The procedure for adding a satellite is the same as for editing a satellite.

7.2 Setup

Use the Setup menu to conﬁgure the system settings of your receiver. The following sub-menus are

available: Language, Output Options, Time Setting, Parental Control and OSD Display. Choose the desired

submenu with pq and press OK to advance.

7.2.1 Language

Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to

highlight the setting you wish to change and tu to change the value of the highlighted setting. Press

OK for a list with all available options for the chosen setting.

Display: This setting affects the menu language of your receiver. All menu’s and

messages will be displayed in this language.

Audio: is the preferred audio language. The receiver will automatically switch audio to

the preferred language whenever available.

Subtitle: Whenever available, subtitles will be displayed in the selected language.

Country: Here you can set your country of residence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7300 CI plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 7300 CI plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info