Bedienungsanleitung Strong SRT 7500 (Seite 9 von 20) (Englisch)

480572

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

PART 2 • English

4.2 Country Selection

Select the desired country by using tu and press OK to continue.

4.3 Antenna Installation

In the Antenna Installation Menu the necessary settings for the dish installation will be displayed. Depending on the

selected country there might have been already done a setup for your satellite dish (Austria and Germany: Astra 19.2E

on DiSEqC input 1/ Czech and Slovakia: Astra 23.5E on DiSEqC input 1). These settings will allow you to receive signal

automatically. If you are using another dish setup please ask your installer for further setup and refer to chapter 5.3.1

Antenna Installation. After you conﬁrmed correct parameters with OK, you will be guided to the next step.

Tip If you see that the signal bar levels are orange you might need to adjust your dish position in small steps

until the signal strength and quality bars turn green. Try to reach the maximum possible strength and

quality level. Once you are sure that the signal cannot be improved, ﬁx the dish on this position.

4.4 Channel set-up

Here you have the opportunity to select desired installation method Preset, Preset Plus or Auto Search. If you select

Preset and Preset Plus, the receiver will load the country speciﬁc channel list. If you select Preset Plus or Auto Search,

you will be guided to the next screen for channel scan.

4.5 Auto Search

Select your preferred channel search method with pq. Via tu you can change the kind of scan process. If you

adjusted these settings according your wishes press OK to start channel search. The search process will take some time

(depending on the chosen search method). After the channel search has ﬁnished, the FIRST TIME INSTALLATION is

completed and the ﬁrst programmed channel will be displayed on screen.

5.0 MAIN MENU

All important settings and features of your receiver can be operated in Main Menu. The Main Menu consists of

following sub-menus: “Program Table”, “Favourites”, “Installation”, “Conﬁguration”, “Timer”, “Games”, “Media Browser”

and “CA System.” To enter Main Menu press the OPTS button in viewing mode.

5.1 Program Table

In Main Menu screen, use the pq buttons to select Program Table and press OK to enter this menu. In this menu,

you can choose between following actions: Select, Move, Delete, Edit and Lock desired channels. With BACK you can

always cancel actions and exit the actual menu or submenu.

Select

In this mode you can select different channels you want to watch and decide maybe afterwards what you want to do with

this desired channel. Use the

pq buttons in the program table to go through the channel list, furthermore you can use

the RED (PG up) and GREEN (PG down) buttons for scrolling page wise. With OK you can switch to selected channel.

The frequency and satellite name of the selected program will be displayed below the picture of this channel.

Move

Here you can change the order of desired channels. Select Move with the

tu buttons, then the channel with the pq

buttons and press OK to mark it for moving (coloured dark blue and marked with move sign). Now you will be able to

choose a new position for the desired channel with the

pq buttons, conﬁrm the new position with OK. If you don’t

want to move the selected channel, you can cancel by pressing BACK.

Delete

Select Delete with the

tu buttons, then with the pq buttons the channel you want to delete and press OK to mark it

for deletion. Pressing OK again will unmark the selection. After you have marked all channels you want to delete, press

BACK. You’ll be asked if you want to delete the selected programs. Select YES to conﬁrm and NO to cancel deletion.

Edit

Select Edit with the

tu buttons, then with the pq buttons the channel you want to edit and press OK to enter

renaming line. Use the NUMERIC buttons to enter the desired name and press OK to conﬁrm. For cancellation press

BACK. Maximum value for inserted characters is 15.

Lock

Select Lock with the

tu buttons, then with the pq buttons the channel you want to lock and press OK to mark it

for locking. First you’ll need to insert your PIN Code (Default: 0000). Then the desired program will show the padlock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7500 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info