Bedienungsanleitung Strong SRT 8200 (Seite 8 von 23) (Englisch)

480565

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

English

WARNING: The batteries should not be recharged, disassembled, electrically short-circuited, be

mixed or used with other types of batteries.

If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH)

types with low self-discharge to ensure long time operation of remote control.

2.5 Using the remote control

Fig. 5

To use the remote control, point it towards the front of your receiver. The remote control supports a

range of up to 7 meters distance to the receiver at an angle of up to approx. +-30 degrees.

NOTE: Managing the receiver will be limited or not possible if there are obstacles between the remote

control sensor (at the front panel of the receiver) and the remote control. Direct sunlight or very

bright light can reduce or disturb the reception of the remote control signals.

3.0 CONNECTIONS

WARNING: Please make sure that connection devices are disconnected from their main power

supplies before connecting these to the receiver.

3.1 Connecting to your aerial antenna

Fig. 6

To receive digital broadcasted signals, your receiver has to be connected to a terrestrial indoor or

outdoor antenna. Use the antenna cable to connect the aerial with the ANT IN connector on the back of

your receiver. Please ensure that a properly shielded antenna cable and suitable connectors are used.

The TO TV connector allows you to loop the antenna signal to a second receiver or TV set.

3.2 Connecting to TV with HDMI cable

Fig. 6

We recommend connecting your TV set with the receiver using a good quality HDMI 1.3 or higher cable

(not included). This connection supports the highest possible quality.

3.3 Connecting to TV with a cinch cable

Fig. 6

Your receiver is also equipped with Audio L, R and VIDEO connectors. As an alternative, use these connections

if your TV set doesn’t have an HDMI connector. Use a cinch cable to establish the connection.

3.4 Connecting to a digital audio ampliﬁer

Fig. 6

By connecting your receiver to a digital ampliﬁer or home theatre system, you can enjoy the best possible

sound quality and multi-channel audio (depending on broadcast). Connect your Digital Audio Ampliﬁer or

home theatre system with a suitable cable to the S/PDIF connector on the back of the receiver.

3.5 Connecting to a digital A/V receiver and TV using HDMI

Fig. 7

By connecting your receiver to an A/V receiver or enhanced digital home theatre system with HDMI, you

will enjoy the best possible sound and picture quality as well as multi-channel audio too (depending

on broadcast). Connect the HDMI output of the receiver to the corresponding input of your A/V system

and then connect the HDMI output of the A/V receiver or home theatre system to your TV set. Select the

correct input on your A/V system to watch and listen to programmes. If your TV set already supports DD

audio we recommend you to use the direct connection as described above in chapter 3.2.

3.6 Connecting an external USB storage device

Fig. 6

NOTE: For details to consider when using a USB storage device please refer to chapter 1.5.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info