Bedienungsanleitung Strong SRT 8200 (Seite 15 von 23) (Englisch)

480565

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Screen Mode: Use t/u to adjust this setting in accordance with the aspect ratio of your TV

set (4:3 or 16:9) and the preferred conversion. Options are: Auto (automatic

detection of aspect ratio), 4:3 Panscan (displays 16:9 broadcasts full screen and

cut upper and lower parts of 16:9 video on your 4:3 TV), 4:3 letterbox (displays

16:9 widescreen broadcasts with black bars on top and under the picture on a

4:3 TV). For a modern 16:9 TV set following options can be set: 16:9 Wide Screen,

16:9 PillarBox (4:3 broadcasts will be shown with black vertical bars on the left

and right side of the image) and 16:9 Pan&Scan. We recommend trying these

settings in order to ﬁnd the option that suits you best. Do not forget about the

possibility to control the TV format via the menu of your TV set.

HDMI Output: Allows you to change the resolution of the HDMI output. If the connected TV

does not support the newly set resolution, then you will see a black screen. In

this case, wait for 10-15 seconds without pressing any button on the remote

control of the receiver, and the previous value will be recovered automatically.

Loop out in stand-by: This allows to by-pass the antenna signal to the ANT OUT connector, where

you may have an additional TV set/receiver connected, in order to receive

analogue/digital broadcasts there too.

Digital audio: Use t/u to adjust this setting in accordance to the used audio equipment. To

loop the digital audio through HDMI or S/PDIF to a connected ampliﬁer, home

theatre or other equipment able to decode AAC and AC3, set RAW HDMI ON.

If neither your TV set nor any other connected audio equipment supports

decoding of AAC and AC3, set RAW HDMI OFF.

6.3.3 Time Setting

This menu allows you to specify the method for synchronising of date and time and you can set the

duration for displaying the information banner.

Time Oﬀset: Use t/u to choose Auto to automatically synchronise time and time zone with

the broadcast, or Manual, to specify the time zone manually.

Region: Use t/u to set your speciﬁc country.

Time Zone: This setting is only available when the Time Oﬀset is set to Manual. You can

use t/u to set the time zone, if the automatic settings in your region are not

supported by the broadcast.

Summer Time: Use t/u to select On or Oﬀ according to your local season.

Banner Time OUT: Use t/u to choose between the available settings: 3s, 4s, 5s, 6s, 7s, 8s, 9s and 10s.

6.3.4 Auto Standby

Auto Standby is a new feature that helps you reduce power consumption. When Activation is set to On,

the receiver will switch to standby if it doesn’t receive any commands for three hours. Set Auto Standby to

Oﬀ to deactivate this function. When the setting is On you can set the Duration Before Standby: Available

settings are: 1 Hour - 12 Hours with steps of one hour.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8200 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info