Bedienungsanleitung Strong SRT 8525 (Seite 10 von 27) (Englisch)

480560

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

PART 2 • English

English

Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will

be present on the ANT IN connector of the receiver. Select Oﬀ for

passive antennas or when connected to a house distribution system.

When all settings have been made, move the highlight to Next and press OK to continue.

The receiver will now advance to the Antenna Adjustment screen.

4.1 Antenna Adjustment

In this menu you can adjust the antenna in order to ensure best signal quality.

Band: Allows you to select the frequency range according to your local

broadcast conditions. The default adjusted UHF range is the

mostly used one, so we recommend not to change this setting.

If you know that the VHF range is used in your country you can

select it with t/u.

Frequency channel: Select a channel/frequency that broadcasts digital TV channels in

the region where you live.

Now you can adjust your aerial antenna to a proper position in order to get the best signal quality

and strength indication displayed.

Afterwards press q to move the highlight to Search and press OK to start the channel scan process.

The receiver will start searching for channels. Information about the scanned frequency, found TV

and radio channels and channel scan progress is displayed on screen. When the channel scan has

been completed, the receiver will tune on the ﬁrst found TV channel.

NOTE: If the receiver hasn’t found any channels by the end of the channel scan, it

is possible that your antenna is not installed/ aligned correctly. To ensure

good results and the proper antenna conﬁguration, refer to qualiﬁed

professionals.

5.0 QUICK GUIDE TO USING YOUR RECEIVER

We at STRONG understand that you can’t wait to enjoy your new high deﬁnition digital terrestrial

receiver. The following quick guide will help you getting familiar with the basic operation of this

device. We do, however, advice you to read the full manual to get the best performance from your

receiver.

To switch your receiver ON or in standby, use the q button on the remote control or on the front

panel of your receiver.

If you will not use the receiver for a longer time, unplug it from the mains by unplugging the power

plug from the outlet.

NOTE: 5 min after switching the receiver to standby it will enter the deep sleep

mode. Within this time the receiver is able to start up quickly. Starting up

from deep sleep takes approx. 40 sec.

5.1 Changing channels

There are diﬀerent ways to change channels:

 Via direct access using the 0~9 buttons.

 Via the channel list through the OK button.

 Via the p/q or P+ and P buttons.

5.1.1 Direct access

To access to a channel directly, simply enter its number with the 0~9 buttons on the remote control.

Channel numbers can be up to four digits long. Entering a number with less than four digits is

possible. Just wait a few seconds and your receiver will switch to the channel number, or just press

OK after inserting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8525 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info