Bedienungsanleitung Strong SRT 8550 (Seite 16 von 28) (Englisch)

751661

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Programming a record timer via the Timer menu

If you want to programme a record timer via the timer menu, select it via the MENU button on the

remote control in viewing mode, option Timer in the menu Settings. This way you are free to programme

start and stop time. For further details about this menu, please refer to chapter 8.3.6 Timer in the user

manual.

1.27.4 Playback

After a recording has been made you will nd a new folder Records created on your external USB storage

device. By pressing u in viewing mode you can access this folder directly. Inside the Records menu the

following functions are supported:

pq To select a recorded event.

OK Starts playback in preview and again in full screen mode.

3 Stops playback

RED Option Opens the option menu to select and deselect for deleting a recorded le(s).

This menu item opens only if you have selected rst a le by using pq.

Marks a recording for deletion. When all recordings you want to delete are

marked, select Deleted Selected press OK. A message will appear to conrm

deleting. By pressing OK again the recordings will be permanently deleted

from your external USB storage device. Select Cancel if you don't want to

delete them or select once more OK to denitely delete.

8.0 MAIN MENU

The main menu gives you access to Installation, Channels, Settings, Multimedia and Network functions. To

access the main menu, press MENU in viewing mode. Throughout the main menu, 9 can be used to get

back to the previous screen and  to quit.

1.28 Installation of channels

Use tu to select the main menu item Installation.

Use pq to highlight the submenu of choice and press OK to select. These submenus are available:

Manual Search, Auto Search, Information, Factory Settings and HPP CA Menu.

1.28.1 Manual Search

This menu allows you to search for channels at a specic Frequency or Channel number.

Use pq to select Scan mode, and select between Free which will only install Free-to-Air channels or All.

This means that channels that are Free-to-Air or scrambled will be searched and stored.

Use pq to select Channel No and select the channel number of the frequency you'd like to search. Press

OK to open a list to make selection faster.

The next option Modulation is to select between Only DVB-T or DVB-T/T2 modulation type.

When in doubt, use the DVB-T/T2 setting.

If you use an active antenna (with built-in amplier), then switch the Antenna Power to On. If you use a

passive antenna (without built-in amplier), then select O.

Highlight Search and press OK to start scanning. New found channels will be added to the channel list.

1.28.2 Auto Search

This menu allows you to search for channels from all available Frequencies or Channel numbers. Be aware

that all previous installed channels and favourite list(s) will be deleted. The new found channels will be

installed in the channel list and afterwards you can create a new favourite list if you like.

Select Scan mode, and select between Free which will only install Free-to-Air channels or All.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8550 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info