65945
11
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
PART 1 • English
7
English
3.4 Connecting to serial cable for downloading software
Connect the RS-232 connector on the back of your receiver to the Serial port of your computer
using a serial cable. Instructions how to download software can be found on our website www.
strongsat.com (support > download). However, this receiver can download new system software
automatically by satellite. (Fig. 9)
4.0 STARTING UP
Ensure that your satellite receiver is correctly connected to your television and dish, and that your
satellite signal is of good quality. (If you are not sure about this then ask your local strong dealer to
check your installation or satellite signal.)
Confirm that the power plug on the receiver is plugged into the wall outlet. Turn on the receiver. The
following picture is shown the first time you switch on the receiver.
It is recommended that you perform the first time installation following the Installation Wizard step
by step. It will help you to easily achieve system configuration and channel installation. If you are a
professional installer then you can skip wizard by pressing MENU button and set-up channels using
the Installation menu.
4.1 Language Selection
Press UP/DOWN to choose your language, press OK to confirm. The Select Satellite menu will appear.
4.2 Select Satellite
Future installation steps are depending from satellite where your dish is aimed.
1. Your dish is aimed to Astra 1C, 1E, 1F or Hotbird satellite.
Press UP/DOWN to select the ASTRA or Hotbird satellite and press OK button on your
remote control.
Follow instruction written on screen. When you have fixed your dish at correct direction
choose NEXT and press the OK button. The Channel Setup menu will appear.
2. Your dish is aimed at another satellite
Select Other in Select satellite menu and press OK, more satellites will be listed. If you
select a satellite in the satellite list, the Configure Antenna menu will appear, please
set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control,
DiSEqC Switch and Antenna mode.
4.3 Antenna mode
1. Fixed dish
Set Antenna mode to Fixed, select NEXT and press the OK button. The Adjust antenna
screen appears, select transponder receivable at your location and adjust the antenna
position for maximum level for the signal strength and quality. When you have completed
the adjustment, choose NEXT and press the OK button. The Channel Setup menu will
appear.
2. Dish mounted on DiSEqC 1.2 motor
Set Antenna mode to DiSEqC 1.2, choose NEXT and press the OK button. The menu
Adjust antenna will appear. Select transponder receivable at your location (choose
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Strong SRT6020 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Strong SRT6020

Strong SRT6020 Bedienungsanleitung - Deutsch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info