Bedienungsanleitung Strong SRT7840 (Seite 17 von 28) (Englisch)

750861

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

English

Antenna Type:

For a fixed dish, with a single LNB, select Fixed-LNBOnly (Default)

For a fixed dish set up, with more than 1 LNB, but max. 4 LNBs, including a DiSEqC 1.0 switch, select Fixed-

DiSEqC 1.0. If selected here, then select the corresponding ports at DiSEqC 1.0 below.

For the use of a SCR system (SatCR, Satellite Single Cable distribution) select SCR and then select the

corresponding User Band in the User Band and User Frequency options below.

For a Motor-driver dish set-up, using a DiSEqC 1.2 motor, select DiSEqC 1.2.

With DiSEqC 1.2 it is necessary to search and store every satellite position manually. This is very cumbersome

(and old fashion) to do so. Select a position (1 to 63) with Go To for a satellite and then with Move drive the

antenna until the satellite is found and optimise reception. Then store the position and satellite with Save

Position. Proceed for the next satellite.

GoToX is the unofficial successor to DiSEqC 1.2, sometimes called DiSEqC 1.3 Modern Motor-drives

are all DiSEqC 1.3 type. It involves a predefined satellite list and corresponding positions

to those satellites, in the receiver and a algorithm to determine where the satellite is, given

its geographical location. Only need is to enter the geographical location where the dish is

installed. All satellites can now be found automatically. If GoToX is selected, set the location

in the options below. At Satellite chose the satellite of your choice.

Satellite: Select a satellite to be configured.

LNB Power: Set the LNB power On or Off.

LNB Type: Select the LNB type. The Universal LNB (09750/10600 MHz) is supported and is the most

common on the market for European Ku-band use. Standard refers to C-Band LNBs, Wide C

refers to wide band C-band LNBs.

LNB Freq: Set the frequency of the selected LNB type.

Default is 9750/10600. The Universal LNB (09750/10600 MHz) is the most common on the

market for European Ku-band use.

It is also possible to select alternative frequencies for Universal LNB types.

Transponder: Select one of the available transponders of the chosen satellites in order to check your

reception or to align the antenna.

Move: To drive the antenna until the satellite is found and optimise reception

Sat Degree: Satellite position.

Ant Position: To enter the geographical position of the dish.

Go To: To make the dish move to the set position.

The following 2 options will only show when at Antenna Type the Fixed DiSEqC 1.0 option is selected.

22KHz Tone: Switch the 22 KHz oscillator signal to ON (22K) or OFF (0). Only for C-Band LNB use. Refer to

manual of LNB.

DiSEqC 1.0: Select the correct port of the corresponding LNB.

Available options: Off, Port A, …, Port D.

The following 2 options will only show when at Antenna Type the SCR option is selected.

User Band Select the User Band you are assigned to in the SCR system. Max. 8 users.

User Frequency Displays the corresponding Frequency for the User Bands. If the User Frequency does not

correspondent with any of the default User Bands for you particular SCR LNB, press OK and

select User Define and enter the correct User Frequency for the correct User Band. Then

press OK again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT7840 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT7840

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info