Bedienungsanleitung SunTech CT40 (Seite 17 von 52) (Englisch)

704206

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 17

Save Current Reading: A quick press gives the user an option to save the patients reading, suggested to be done after

each reading.

Access Previous Reading: A long press (holding the button down for 4 seconds) gives the user the option to access

the bank of prior readings. Please see Section 4 to read more about the saving and accessing saved readings.

Toggle Mode Button

Press this button to toggle between three different BP measurement modes: Single Measurement, Averaging

Measurement and Auscultatory SphygMode.

A quick press gives the user an option to switch between BP measurements modes.

A long press (holding the button down for four seconds) gives the user the option to switch between pediatric or

adult mode. More information on switching from adult to pediatric mode can be found in Section 5.

Selection Knob

This round knob rotates clockwise and counterclockwise and can be pressed in to select different options on the

SunTech CT40. This button can be used to change parameters and to set the intended parameter.

Start/Stop Button

Press this button to start or stop a BP measurement.

Home Button

Pressing this button returns you to the single measurement mode.

Monitor Setup

Press the power button to start Initial Power-up. The display will gradually illuminate over a 3-second period. If this is

the first time the device has been turned on since it left the factory or since the device was set to factory defaults, the

user will be prompted to set the time and date in the following format: MM.DD.YYYY HH:MM:SS. The “MM” portion

of the field will flash first, prompting you to set the month. Turn the Select Knob to select the appropriate month and

press the Selection Knob. Then the next field, “DD” will flash, prompting you to select the day, and so on and so forth,

until you have set “SS” for seconds.

After setting the date and time, the device is ready to use! It is possible to make additional configuration changes to

the SunTech CT40 using the Advanced Configuration Application.

To Set the Time and Date

The time and date can be changed by simultaneously holding both the Power and Start/ Stop buttons for 6 seconds.

Refer to the previous section “Monitor Setup” for instructions on setting the time and date using the selector knob.

The SunTech CT40 Vital Signs Monitor also allows for Automatic Time Synchronization via Network (NTP) settings.

Refer to the advanced configurations manual for information regarding either of these changes.

Visual Alarms

When an error occurs, the Warning icon will blink, in addition to the relevant parameter experiencing the error.

Blood pressure error is displaced in the BP heart rate field.

Temperature error will displace in the lower right hand.

SpO2 error will displace in lower left side of the screen.

Battery symbol will flash if error is related to battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SunTech CT40 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SunTech CT40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info