Bedienungsanleitung SunTech CT40 (Seite 18 von 52) (Englisch)

704206

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 18

Depending on the out-of-range value, the display will indicate whether the value is out-of-range (hi) or out-of-range

(lo). If the out-of-range parameter is the systolic or diastolic pressure (or both), and MAP is enabled, MAP is not

displayed for that measurement. NOTE: MAP is not available in the U.S.

See Section 12, “Status Messages and Alarms,” for more details.

4. Good to Know Before You Begin

Power Modes

Initial Power-up occurs the first time the device is turned on after being received from the factory, after the device

has been reset to factory defaults or after the battery has been changed. See “Monitor Setup” for information about

Initial Power-up.

Nominal Power-up refers to every time the device is turned on after Initial Power-up. Simply press the power button

and the display will illuminate.

NOTE: The blue LED around the Selection Knob will be lit whenever the device is powered on.

Power-down occurs when you press the power button when the device is powered up. During power-down, all LCD

segments and icons illuminate for 1 second and then the entire display gradually darkens from normal brightness to

black and then one beep sounds. At this point, the device enters Sleep Mode, a low-power state, and is considered

off.

Automatic Power-down occurs when the device has not been used (i.e., no measurements taken, or buttons pressed)

for 1 hour. The device will automatically execute the Power-down sequence and enter Sleep Mode.

Your SunTech CT40 offers flexibility to function in ways that best meet your work setting.

Documenting Measurements

Before you start taking measurements, it’s important to document the patient ID per your facility’s procedures. To do

so, the barcode scanner must be used to enter the patient ID into the CT40.

With a Barcode Scanner

If your SunTech CT40 is connected to a barcode scanner, you can scan your patient’s barcode ID and it will show at

the top left of your screen. Then, the patient ID will remain attached to all measurements taken, saved in memory,

and/or sent to your facility’s EMR.

Without a Barcode Scanner

If you don’t require a barcode scanner, all measurement results will be displayed on the main screen and can be

saved to the device’s memory, written down in a chart, printed out (with optional thermal printer) or captured in

another way that meets your facility’s documentation procedures.

Printing

The SunTech CT40 can be connected to an optional SunTech thermal printer to easily print out measurement results.

See Section 11 for ordering information.

After connecting the optional CT40 thermal printer (see Section 2 and Section 3), ensure that the green LED on the

top of the printer is lit and unblinking before printing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SunTech CT40 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SunTech CT40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info