Bedienungsanleitung SunTech CT40 (Seite 27 von 52) (Englisch)

704206

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 27

The sensor is too tight.

There is excessive illumination from light sources such as a surgical lamp, a bilirubin lamp, or sunlight.

A blood pressure cuff is inflated on the same extremity as the one with a SpO2 sensor attached.

The patient has hypotension, severe vasoconstriction, severe anemia, or hypothermia.

There is arterial occlusion proximal to the sensor.

The patient is in cardiac arrest or is in shock.

NOTE: See SP02 Sensor Specifications Table on page 45, the range of the peak wavelengths and maximum optical

output power of the light emitted by the pulse oximeter probe, which can be especially useful to clinicians.

NOTE: This device does not include an alarm system that detects an SpO2 or pulse rate physiological alarm condition.

This device is not designed for long-term monitoring and should only be used for spot-check measurements.

System Description:

The SunTech CT40 spot check device with pulse oximetry module consists of a base CT40 device for the display of

SpO2 measurement data and other user information, either a ChipOx or Masimo SET SpO2 module which is attached

to the CT40 base unit as described in Section 2, and the specific reusable pulse oximeter probe and/or cable that

comes packaged with each module. Device setup is described in more detail in Section 2. Both the Masimo® SET and

ChipOx SpO2 modules are calibrated to display functional oxygen saturation (SpO2).

Taking SpO2 Measurements:

1. Insert a finger (preferably the index, middle or ring finger) into the SpO2 sensor until the end of the finger reaches

the finger stop. Do not use the thumb.

2. The fingernail should face the side with the red light. Make sure that long fingernails do not interfere with proper

finger position

3. An SpO2 reading will be displayed after a few seconds. Remove the finger from the SpO2 sensor, and the last

measurement will be displayed and flashed.

4. If the sensor is not removed from the finger, SpO2 readings will be automatically stopped after 10 minutes of

continuous measurement, and the last measurement will be displayed and flashed.

5. To start a new measurement, re-apply the SpO2 sensor to the finger as described in Step 1.

NOTE: If the signal quality from the sensor drops below 90%, no measurement will be displayed in the SpO2 section

, and the percent symbol will begin flashing. Check sensor for correct placement and usage.

Special Notes for Masimo® SET SpO2 module:

NOTE: Possession or purchase of this device does not convey any express or implied license to use the device with

unauthorized sensors or cables which would, alone or in combination with this device, fall within the scope of one or

more of the patents relating to this device.

NOTE: If the accuracy of any measurement does not seem reasonable, first check the patient’s vital signs by alternate

means and the check the MS board pulse oximeter for proper functioning.

NOTE: A functional tester cannot be used to assess the accuracy of a Masimo pulse oximeter sensor or pulse oximeter.

Using Clinical Dynamics SmartSat SpO2 simulator, the device can display the entire range of SpO2 values.

Masimo® Sensors:

Before use, carefully read the M-LNCSTM DCI/DCIP sensor directions for use, which includes cleaning and disinfection

instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SunTech CT40 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SunTech CT40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info