Bedienungsanleitung SureFlap Microchip Cat Flap - serie nr 2000000 plus (Seite 11 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

782757

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

19 20

Stack the tunnel extenders together and then attach them

to the end of the cat flap's tunnel, using all weather tape

between each join to hold them together. Do not glue the

tunnel extenders or cat flap together. From the inside of the

house, feed the extended tunnel into the hole in the wall until

the cat flap is flush against the wall. If no adjustment to the

hole shape or size is needed then you are at the point where

you can attach the cat flap to the inside of the house.

The cat flap can be secured directly to your inside wall.

To access the screw holes needed, you have to unscrew

the front frame from the tunnel. To do this, first remove

the battery cover and screw covers, then unscrew the 4

screws and lastly pull the tunnel and front frame apart.

Now locate the 4 screw holes, they are the

larger holes in the corners of the cat flap.

Mark the hole positions using a sharp pencil.

To extend the cat flap's tunnel through to the outside

wall, you need to use the tunnel extender accessories

to make up this length. To calculate how many

extenders you will need, please go to page 17. It is

important to remember that the end has to stick out by

at least 10mm (") for the external frame to rest on.

50mm

10mm

Replace the cat flap, with its extended tunnel, back into the

hole. Then, using the appropriate screws for your wall plugs,

screw the cat flap to the wall - see the diagram.

Screw the front frame back onto the tunnel. It is important

that these parts are fitted together correctly, please ensure

that the gap between the parts is no bigger than a credit

card thickness. Once screwed together put battery cover and

internal screw covers back onto your cat flap.

Now remove all of the material in the centre using the most

suitable tools for the material you’re cutting. We do not

recommend that you cut through to the outside in one go.

Cut away material on the inside of the house first and then

move outside to cut the remainder of the hole. Try to keep the

hole within the outlined area otherwise it will be too big.

We recommend using one of the tunnel extenders to make

sure you have a clear path through the wall. Once this is

the case, clear away any dust and debris.

Remove the cat flap from the wall and place it away from

the work area. Drill the four holes using the appropriate drill

bits to suit the construction of your wall, being careful not to

break through the edge of the main hole. Once drilled, put

the wall plugs into each of the holes.

Now you can move to the outside of the house. The extended

tunnel should be poking out of the hole. Place the external

frame over the tunnel.

Lastly, use an All-Weather sealant to seal the gap

between the tunnel and the external frame. We

also recommend putting some sealant around

the join between the external frame and the wall.

Now, insert the two screw caps into the external frame.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SureFlap Microchip Cat Flap - serie nr 2000000 plus Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info