Bedienungsanleitung Synq SMX-1 (Seite 8 von 43) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

468139

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

ENGLISH USER MANUAL

SYNQ 11/82 SMX-1 DJ-MIxer

41.INPUT SOURCE SELECTOR: Used to select the correct input on each channel:

Phono, line, aux or mic. On some channels there are additional input selectors on

the back, near the input connectors!

Hint: Line, Aux, CD, Tuner, etc…are differentnames for inputs with almost the same signallevels.

42.GAIN LEVEL: Adjusts the input level on each channel, range goes from zero to

maximum. Use this control to adjust the level on the VU-meter at about 0dB.

CONNECTIONS

When connecting or changing connections, always turn off the units before.

This connection diagram is just an example of what is possible. Many other connections

are possible. Just keep the following remarks in mind:

 Always connect cinch cables in the same way:

o white or black cinch connector  left channel

o red cinch connector  right channel

ENGLISH USER MANUAL

SYNQ 12/82 SMX-1 DJ-MIxer

 When you connect a CD-player, Cassette deck, MD-player, tuner, video recorder etc. to

one of the inputs, don’t forget to put the source selector of that channel to “LINE” or

“AUX”.

 When connecting a microphone to channel 4, switch the source selector to “MIC”.

 When you connect a turntable to one of the inputs, don’t forget to put the source

selector of that channel to “PHONO”. (attention: newer turntables may have a line

output, read the user manual of your turntable to be sure)

 Many Turntables have a GND-connection. It is preferable to connect this signal ground

to the SMX-1. Use the GND-connections, close to the signal input connectors.

 The Record input of an analog recording device can be connected to the record output

of the SMX-1 to make analog recordings.

 If you have a digital recorder, connect it to the coaxial digital output of the mixer. You

can obtain outstanding digital recordings.

 To ensure the best possible sound quality, short-circuit pins are installed on all unused

phono inputs. When connecting a turntable to the SMX-1, first remove the short-circuit

pins of the input you want to use. Keep these short-circuit pins in a safe place for

eventual later use.

CHANGING THE FADERS

One of the big advantages of this mixer is the possibility to change the channel faders,

even while the mixer is in use.

This is what you must do to change a channel fader:

 Remove the fader knobs from the faders.

 Remove the 4 screws that hold the small

front panel around the faders.

 Remove the 3 screws of the fader you want

to change.

 Gently remove the fader from its position.

 Put the new fader gently in place. Be sure

to fit the contacts into the connector on the

mixer PCB-board.

 Put the 3 screws from the fader back in

place

 Put the small front plate back in place with

the 4 screws.

Done!

This is what you must do to change the cross fader:

 Remove the fader knob from the cross fader.

 Remove the 2 screws that keep the cross fader in place.

 Gently remove the fader and the cover plate from their position.

 Unplug the cross fader from the cable (unplug the cable by pulling the connector, NOT

the cable!)

 Press the new cross fader on the cable.

 Put the cross fader back in place with the small cover plate and the 2 screws.

Done!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Synq SMX-1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info