Bedienungsanleitung Tascam CD-200BT (Seite 11 von 32) (Englisch)

587253

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

TASCAM CD-200BT 11

2 – Names and functions of parts

e PLAY MODE/PLAY AREA [SOURCE SEL] button

Press briefly to change the playback mode.

The four playback modes are continuous, single, random

and program. (See “Playback modes” on page 18.)

Press and hold this button to select ALL PLAY or FOLDER

as the play area during data CD playback. (See “Setting the

playback area” on page 18.)

Press this button while pressing and holding the DISPLAY

[SHIFT] button to cycle through the current source options

in the following order.

Current source order

NOTE

AUX IN cannot be selected if nothing is connected to the

AUX IN jack.

CAUTION

The playback mode and playback area settings can be

changed when the current source is Bluetooth, but these

settings have no effect on Bluetooth playback.

r REPEAT/INTRO CHECK [PITCH] button

Press to turn the repeat playback function ON/OFF. (See

“Repeat playback” on page 22.)

Press and hold this button during playback or when stopped

to use the intro check playback function. The first 10 seconds

of each track on the CD will be played back one after the

other. During intro check playback, press and hold this

button again to return to the previously active playback

mode and continue playing back the current track. (See “Intro

Check function” on page 24.)

While pressing and holding the DISPLAY [SHIFT] button,

press this button to turn the CD playback pitch control

function ON/OFF. (See “Pitch control” on page 24.)

CAUTION

The repeat setting can be changed when the current source

is Bluetooth, but this setting has no effect on Bluetooth

playback. Moreover, when using Bluetooth the intro check

function cannot be used.

t FOLDER g/t [PITCH −/+] buttons

Use these buttons when the current source is a CD and the

playback area is FOLDER to change the playback folder. (See

“Setting the playback folder” on page 20.)

Use these buttons when the current source is a CD and the

playback area is ALL PLAY to skip between folders.

Press this button while pressing and holding the DISPLAY

[SHIFT] button to set the pitch control value. (See “Pitch

control” on page 24.)

Rear panel

y ANALOG OUTPUT (UNBALANCED) jacks

These jacks output analog signals (Standard output: –10

dBV) of the CD or Bluetooth playback signal or the signal

input through the AUX IN jack.

u DIGITAL OUTPUTS (COAXIAL) jack

This jack outputs the CD playback signal in S/PDIF digital

format.

i DIGITAL OUTPUTS (OPTICAL) jack

This jack outputs the CD playback signal in S/PDIF digital

format.

NOTE

• Audio from Bluetooth playback and audio input through

the AUX IN jack can only be output as analog signals. These

audio sources cannot be output as digital signals.

• The sampling frequency of this unit’s digital output is always

44.1 kHz regardless of the playback file sampling frequency.

• Digital output is possible when the pitch control function is

on with CD, but the sampling frequency is changed by an

amount proportional to the pitch control value.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam CD-200BT Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info