Bedienungsanleitung Tascam CD-RW900MKII (Seite 28 von 36) (Englisch)

587262

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

28 TASCAM CD-RW900MKII

Unfinalizing CD-RW discs

If a CD-RW disc has been finalized, it is possible to erase the

Table of Contents in the following way:

1. With the finalized disc loaded and the unit in stop

mode, press the ERASE/DEL key on the front panel

or the ERASE key on the remote control.

Rotate the MULTI JOG dial or press the SKIP key

on the remote control to select UNFINALIZE?.

Push the MULTI JOG dial or press the ENTER key

to confirm.

If you do not want to proceed with the unfinaliz-

ing process, press the ERASE/DEL key on the front

panel or the SKIP key on the remote control.

2. The display shows Sure?

If you do not want to proceed with the unfinalizing

process, press the STOP key.

3. To start the unfinalizing process, press the MULTI

JOG dial or the ENTER key again.

When unfinalization has been chosen, the display

shows Erase flashing and the remaining time.

The unit starts counting down from a time shown

on the display.

4. When finalization has been finished successfully,

Complete appears on the display, and the TOC indi-

cator will go off.

Finalizing

As has been explained earlier (“About Finalizing” on page 8), in

order for a disc to become a standard CD, it must have a Table of

Contents (TOC) written to it. This process is known as finaliz-

ing.

An unfinalized disc can always be distinguished on the

CD-RW900MKII by the TOC indicator under the disc type on the

display being unlit when the disc is inserted.

To finalize a disc:

1. Load the unfinalized disc, and with the unit in stop

mode, press the FINALIZE key.

The display shows FINALIZE?

If you do not want to proceed with the finalizing

process, press the FINALIZE/INS key on the front

panel or the FINALIZE key on the remote control.

2. To start the finalizing process, push the MULTI JOG

dial or press the ENTER key on the remote control.

The display shows Sure?

If you do not want to proceed with the finalizing

process, press the STOP key.

3. When finalization has been chosen, the display

shows the TOC flashing and the remaining time. The

unit starts counting down from a time shown on

the display.

4. When finalization has been finished successfully,

Complete appears and the TOC will be lit on the

display.

NOTE



During the ﬁnalizing process, all key presses are ignored.

This section deals with the actions taken after record-ing: final-

izing for CD-R and CD-RW discs, and erase operations for

CD-RW discs.

Once finalized, CD-R discs are truly final—no more can be

recorded on them. By contrast, CD-RW discs can be “unfinal-

ized” using the CD-RW900MKII, i.e. their TOC can be deleted,

and if there is space, further material can be recorded on them.

Even if the disc is full, tracks can be erased following the unfi-

nalize process, and new material can be recorded.

6 − After recording

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam CD-RW900MKII Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info