Bedienungsanleitung Tascam CD-RW901MKII (Seite 27 von 44) (Englisch)

587263

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

TASCAM CD-RW901MKII 27

5 − Recording

Basic recording

1. Load a recordable disc into the unit. As the disc

loaded, the display shows TOC Reading, with the

period flashing.

2. Press the INPUT SELECT key to select a recording

source (see “Input selection” on page 26).

If a digital source is selected, and the connection

or the signal are improper, the error message D -IN

UNLOCK! will appear on the display.

3. Press the RECORD key. The unit enters record

ready mode, as shown by the REC and READY indica-

tors on the display.

NOTE



As the unit enters record ready mode, the display

shows Now OPC (Optimum Power Control) occasion-

ally, as the unit prepares to record on the disc.

To adjust the level of the source, following the

guidelines in “Input selection” on page 26.

NOTE



The red “OVER” indicators on the meters should never

light. Unlike analog equipment, digital audio units

pro-duce extremely unpleasant sounds when distort-

ed, and there is no “headroom” after the 0 mark. If

recording digitally from a commercially-produced

CD, the volume set in the menu should be 0 dB. This

will maintain all the dynamic range of the source CD

without clipping. Only boost the signal if the source is

exceptionally quiet.

An analog signal input at nominal level, with no cut

or boost from the volume controls, is equivalent to a

reading of −16 dB on the meters.

4. Press the PLAY key to start recording.

Pressing the PAUSE key stands by recording tempo-

rarily. To restart recording, press the PAUSE key or

PLAY key again.

5. Press the STOP key to stop recording.

When recording stops, the display shows

PMA Writing (Program Memory Area) flashing

for a few seconds as the unit writes to the disc.

NOTE



When PMA Writing is shown on the display, all keys

are ignored.

To conﬁrm the total recording time, use the REC TIME

option in the SYSTEM sub-menu (see “Operation

basics” on page 16).

NOTE



Do not vibrate the unit or turn off the power when the

unit writes to the disc, otherwise, recording will fail.

Full disc

If the disc becomes full during recording, the unit will

automatically insert a fade-out. For example: When recording

a long program, just before the end of the disc is reached, the

unit starts a fade-out over four seconds and the display will

show Fade Out.

When the fade-out has finished, the display shows Disc

Full!. Press the STOP key to exit.

If the disc is a CD-RW, the final track can be erased, if

required (see “Erasing” on page 34) and the disc then

finalized. If the disc is a CD-R, it must be finalized prior to use

(see “Finalizing” on page 33).

Time display while recording

When in record or record ready mode, repeated presses of the

TIME key cycle through four different time modes:

•

Elapsed track time (no display light indication)

•

Remaining track time (REMAIN is lit in the display)

•

Elapsed disc time (TOTAL is lit in the display)

•

Remaining disc time (TOTAL and REMAIN are lit in

the display)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam CD-RW901MKII Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info