Bedienungsanleitung Tascam CD-RW901MKII (Seite 28 von 44) (Englisch)

587263

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

28 TASCAM CD-RW901MKII

5 − Recording

Sync recording

1. While recording standby mode, press the SYNC

REC key.

2. Set the signal detection threshold level. Use the

SYNC LEVEL option in the REC sub-menu (see

“Operation basics” on page 16).

Rotate the MULTI JOG dial to adjust the level. The

level can be set from -72 dB to -24 dB in 6 dB incre-

ments. The default setting is -54 dB.

Press the MENU key or push the MULTI JOG dial to

enter and return to recording standby mode.

3. Input the source signal.

Recording begins automatically when the source

signal is detected. The source signal should be high-

er than the adjusted threshold level.

S_LVL

Start of recording

level

time

Noise level

NOTE



After SYNC is set, over one second of silence which is

under the adjusted threshold level is required to start

recording automatically. Otherwise, the unit does not

begin recording even if it is detecting a signal.

When audio signal is not detected for more than five seconds,

the CD-RW901MKII automatically will stop recording and

enter record standby mode.

S_LVL

REC ready

level

time

Five seconds

NOTE



When the input level drops below the adjusted thresh-

old level for more than ﬁve seconds, recording stops

automatically and enters in recording ready mode.

3. To cancel the Sync recording mode, press the

SYNC REC key. Recording returns to normal and

continues till you press the STOP key or the source

signal stops.

Pressing the STOP key stops recording.

The setting remains when the function is set on again.

Synchronized recording

Synchronized recording basically means that recording will

begin automatically when a signal is received, and will stop

when the signal ends.

The SYNC indicator appears on the display.

Starting playback of the source automatically starts recording

on the CD-RW901MKII if Sync function is on (see “Sync

recording” below) and manual record start is disabled.

Advanced recording

Fade-in and fade-out recording

At the beginning and end of recording, fade-in and fade-out

effects can be performed.

1. When stopped or when in recording standby mode,

set the operation using the following menu options

on the REC sub-menu (see “Operation basics” on

page 16).

FADE IN?

The length of the fade in to the normal level can be

set between 1 and 30 seconds in 1-second increments

(default setting: 3 seconds).

FADE OUT?

The length of the fade out into complete silence can be

set between 1 and 30 seconds in 1-second incre-ments

(default setting: 3 seconds).

The display shows Fade Out>XXs or Fade In>XXs.

2. In recording standby mode, press the FADER key on

the remote control.

Recording begins and the sound fades in. After the

preset fade-in time, the sound is at normal level.

3. During recording, press the FADER key on the

remote control when you wish to fade-out the sound.

Fade-out begins with Fade Out flashing on the

display then the unit enters recording standby mode.

4. Press the STOP key and the PMA writing will begin.

NOTE



Fade-in or fade-out function can be operated only by

pressing the FADER key on the remote control unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam CD-RW901MKII Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info