617904
13
Zoom out
Zoom in
Vorherige Seite
1/156
Nächste Seite
TASCAM HS-2000
13
2 − Names and functions of parts
Rear panel
hANALOG IN [LINE] connectors (L/R)
These are balanced analog XLR connectors for line
input.(1: GND, 2: HOT, 3: COLD)
jDIGITAL IN [LINE] connector
This balanced XLR connector is for digital audio input
in AES3-2003/IEC60958-4 (AES/EBU) or IEC60958-3 (S/
PDIF) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
The built-in sampling rate converter can handle 32–
192 kHz.
kANALOG OUT [MONITOR] connectors (L/R)
These balanced analog XLR connectors output the left
and right monitoring signals. (1: GND, 2: HOT, 3: COLD)
lRS-232C connector
Connect an external controller, for example, to this
9-pin
D-sub connector for RS-232C serial control.
NOTE
It cannot be used at the same time as the RS-422
connector. (See “RS-232C page” on page 107.)
;PARALLEL connector
Connect a TASCAM RC-SS20 or other external
controller to this 25-pin D-sub parallel control
connector.
zAC IN connector
Connect the included power cord here.
xANALOG OUT [LINE] connectors (L/R)
These balanced analog XLR connectors are for line
output. (1: GND, 2: HOT, 3: COLD)
cDIGITAL OUT [LINE] connector
This balanced XLR connector is for digital audio output
in AES3-2003/IEC 60958-4 (AES/EBU) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
vREMOTE connector
Connect a TASCAM RC-HS32PD or RC-HS20PD remote
control (sold separately) here.
CAUTION
Never connect this to a network using an Ethernet cable.
Doing so could damage this unit or network equipment.
bRS-422 connector
Connect an external controller, for example, to this
9-pin D-sub connector for RS-422 serial control.
NOTE
It cannot be used at the same time as the RS-232C
connector. (See “RS-422 page” on page 108.)
nTIMECODE INPUT connector
This balanced XLR connector is for SMPTE timecode
input.
mTIMECODE OUTPUT connector
This balanced XLR connector is for SMPTE timecode
output.
,WORD/VIDEO IN connector
This BNC-type connector accepts a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz) or a video reference
signal (NTSC/PAL black burst signal, HDTV Tri-Level
signal).
Use the switch to turn the integral 75Ω terminator on
or off.
.WORD/VIDEO THRU/OUT connector [cut WORD”]
This BNC-type connector outputs a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz or thru) or a video
reference signal (IN connector signal thru only).
Use the THRU/WORD OUT switch to set the signal
output.
/75Ω ON/OFF/THRU/WORD OUT switch
Use this three-way switch to make one of the following
settings.
Terminator OFF and WORD/VIDEO THRU
Terminator OFF and WORD OUT (no VIDEO OUT)
Terminator ON and WORD OUT (no VIDEO OUT)
!ETHERNET connector
Use this Ethernet connector to connect the unit with
a network for file transfer and to control this unit from
another device on the network.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam HS-2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info