617904
15
Zoom out
Zoom in
Vorherige Seite
1/156
Nächste Seite
TASCAM HS-2000
15
2 − Names and functions of parts
When REMOTE Select (pin 14) is set to high, it can be used
as an ordinary parallel controller.
When set to low, flash start mode is enabled. In addition,
depending on the Flash Page high/low setting (pin 20),
the key assignments are as follows.
Pin 14 Pin 20 Flash start take
Low High 1–10
Low Low 11–20
TALLY_BC_*: Use menu setting to switch output (OFF, ON)
(When an RC–SS20 is connected set output to OFF.)
TALLY_BC_STOP/CM/END: 250msec pulse output
TALLY_BC_STANDBY/PAUSE: Level output
The following example is of a connection that uses a fader
to start and stop playback of this device.
For information about the assignment of AUX 1–3 (pins
17–19) functions, see the “PARALLEL page” of “Remote
settings (REMOTE SETUP)” on page 106.
NOTE
When controlling this unit with an external device
that is connected to the PARALLEL connector, by
simultaneously inputting PLAY and RECORD signals
while this unit is stopped, you can start recording
immediately.
In timeline mode, by simultaneously sending PLAY
and RECORD signals during playback, you can start
overwriting the recording.
RS-232C connector
The RS-232C connector on the rear panel can be
connected to an RS-232C connector on a computer to
allow control of this unit from that computer.
Make settings related to communication on the RS-232C
page of the
REMOTE SETUP
screen. (See “RS-232C
page” on page 107.)
NOTE
Please contact TASCAM customer support for information
about this unit’s RS-232C command protocol.
RS-422 connector
You can control this unit remotely by connecting the RS-
422 connector on its rear panel to a controller or editor
compatible with the SONY P2 protocol (RS-422).
Use the
REMOTE SETUP
screen RS-422 page to make
settings related to operation. (See “RS-422 page” on page
108.)
NOTE
Please contact TASCAM customer support for information
about this unit’s protocol compatibility.
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam HS-2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info