Bedienungsanleitung Team HC 15 (Seite 10 von 35) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487002

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Generated by Unregistered Batch DOC TO PDF Converter

2011.3.804.1511, please register!

Copies of the I/B. Please reproduce them without any changes

except under special instruction from Team International

BELGIUM. The page must reproduced and folded in order to

obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).

The page must be folded in order to keep the good numbering

when you turn the page of the I/B . Don’t change the page

numbering. Keep the languages integrity.

Assembly page 10/35

Fax +32 2 359 95 50



OUTLINING

 Outlining requires no attachment combs. Take the clipper and push the lever (see next

paragraph) up to the close-cut position.

 Comb hair into the required style. Start from the outline of the ear by placing the side of the hair

clipper on the skin and following the roundness of the ear (6). To draw the sideburns and the

nape of the neck, place the hair clipper in the wrong side (with the cover facing the head), the top

of the blades perpendicular to the skin and cut to the desired length (7). If necessary, insist on the

reluctant hair.

 When you get used to your hair clipper, you will be able to make layers simply by changing the

length of the combs in function of the cutting zone. This handling ask for a special dexterity in

order to obtain a correct result.

LEVER

This lever has two main functions:

 Regulation of the cutting length because in the position short hair (lever pushed to the front side)

you can cut the length of the used combs or make outlining by pulling it to the backside, you can

make the cutting length longer (this allows middle cutting lengths above the 4 delivered combs).

 Partial cleaning of the blades when in use by to and fro motions in order to remove the hair

blocked in the blades.

ADJUSTABLE LEVER

 Your clipper was carefully examined before leaving our factory to ensure that the blades were

oiled and aligned.

 Blades must be realigned if they have been removed for cleaning or replacement. Therefore, as

the lever is pushed to the front side in short hair position, the end of the top blade teeth is

 approximately 1.2 mm away from bottom blade. Compare your clipper blades with the sketch

(9).

 If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for a few

moments, turn off and unplug. Loosen screws slightly and turn the upper blade until a correct

alignment. Then tighten screws once the blades are aligned (10).

 Change the blades as soon as they become blunt.

 To clean the blades, use the small brush delivered with your appliance and if necessary, remove

them completely.

OIL

 To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).

Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will

evaporate and leave the thick oil which may slow down the blades' motion.

POWER SCREW

 The power screw allows you to adjust the power. It has been adjusted before leaving the factory;

however, if the voltage in your home is low, you may need to re-adjust it. To adjust, use a

screwdriver or a thin coin to turn power screw clockwise until it stops (13). Then slowly turn

power screw out (counter-clockwise) until noise reduces. This is the maximum power setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team HC 15 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info