640528

Tecomec MIDI Jolly Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
4
EN
A copy of this manual is delivered with each grinder.
NB: The descriptions and illustrations contained in this manual
are not binding. The manufacturer reserves the right to bring
about any modications without updating this manual.
ELECTRICAL CHAIN GRINDER FOR SAWS
midi jolly
230 V~ -
midi jolly
120 V~
SPEED MASTER
230 V~ -
SPEED MASTER
120 V~
easy grinder
230 V~ -
easy grinder
120 V~
CHARACTERISTICS OF THE MACHINE
- Manufacturer: Tecomec
- Machine: Electrical chain grinder
midi jolly
–
SPEED MASTER
–
easy grinder
for saws
DATA AND MODELS
- models:
midi jolly
230 V~ -
midi jolly
120 V~
SPEED MASTER
230 V~ -
SPEED MASTER
120 V~
easy grinder
230 V~ -
easy grinder
120 V~
- installed power: electrical motor 50Hz 85W voltage 230V
~
– 60Hz
85
W voltage 120V
~
- insulation class II
- grinding wheel dimensions: outside diameter105mm, inside
diameter 22.3mm
- thickness: 3.2 – 4.7 – 6mm
- maximum speed: 5000 min
-1
(15 min)
- sound pressure level: 76dB (A)
- level of vibrations transmitted to the handle: < 2,5 m/s
2
- the declared vibration total value has been measured in accordance
with a standard test method and may be used for comparing one
tool with another;
- the declared vibration total value may also be used in a preliminary
assessment of exposure.
- the vibration emission during actual use of the power tool can differ
from the declared total value depending on the ways in which the
tool is used;
- the need to identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions of use
(taking account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle in addition
to the trigger time).
- type of chains: pitches – 1/4” .325” – 3/8” – .404”
- weight of the complete machine: 19.6N (2 kg)
- accessories provided: 1 wheel thickness: 3.2mm, 1 F r o n t
protection, 1 Shield guard screw, 1 Rear h ed protection, 1 dressing
stone; 1 template ; 1 handle. 1 screw M6x25
INTRODUCTION
Keep this manual with care.
To ensure the correct use of the grinder and to prevent accidents,
do not start working without having read this manual carefully.
This manual explains the operation of the machine components and
provides instructions for carrying out the checks and maintenance
required.
WARNING – Any maintenance operations not described in
this manual shall only be carried out by an authorized service
center. To guarantee the efcient and consistent operation of
your grinder, worn or broken parts shall only be replaced using
ORIGINAL SPARE PARTS.
SAFETY
ATTENTION! When you use electrical machines, you
should always observe basic safety precautions to
reduce the risk of re, electric shocks and personal
injuries.
- Do not leave the machine out in the rain.
- Do not use the machine in damp or wet places.
- Keep the work area well lit.
- Do not use the machine near ammable liquids or gas.
- Make sure the voltage and the frequency written on the rating
nameplate match those of the mains.
- Make sure the switch is turned off (pos. 0) before you plug the
machine into the mains to prevent it from starting up accidentally.
- Unplug the machine from the mains when it is not in use, before you
start any maintenance jobs and when you replace any accessories
(i.e. grinding wheel).
- Before you actually use the machine, make sure it is able to work
appropriately and efciently: check the integrity of the shield guard
in particular.
- Check the alignment and adherence of moving parts, make sure
nothing is broken, check the overall assembly and any other
conditions that may affect operation.
- The grinding wheel safety guards and any other parts damaged
shall be repaired or replaced by a skilled technician, unless specied
otherwise in this manual.
- Have faulty switches replaced by a skilled technician.
- Keep anyone that is not involved in the job well away from the work
area, especially children. Do not let them touch the machine or the
extension lead.
- Wear safety goggles and gloves.
- Wear a face mask or dust mask if the process creates dust.
- Do not wear baggy clothing or jewelry, which could get caught up in
moving parts.
- Wear a protection cap and tie long hair back.
- Wear non-slip shoes when working outdoors.
- Always stand appropriately and balanced on both feet.
- Always keep your eyes on the job, without distraction. Use your
common sense and do not use the machine if you are tired.
- Always make sure the hex spanners have been taken off the
machine before using it.
- Keep the work area clean and tidy. Untidy work areas and benches
could cause accidents.
- Do not touch earthed surfaces with any part of your body.
- Always use the vise to rmly hold the chain to be sharpened. Never
sharpen the chain while holding it with your hands.
- Do not force the machine to work at a higher speed than that
envisaged.
- Never stop the grinding wheel with your hands, even after the motor
has been switched off.
- When using the machine outdoors, use extension leads approved
for such use and marked accordingly.
- Never pull on the power cable to unplug the machine from the
mains. Keep the cable away from heat, oil and sharp edges.
- Do not use the machine if the switch does not switch on or off.
- The use of accessories (i.e. grinding wheel) different from those
recommended by the manufacturer could cause injuries.
- Do not tamper with the safety devices.
- Look after the machine with care.
- Follow the instructions when replacing accessories.
- Every now and again, visually check the machine cable and have it
repaired by a specialist if you should notice any damages.
- Every now and again, visually check the extension leads and
replace them if damaged.
- Keep the operating handles dry, clean and free from oil and grease.
- When the machine is not used, keep it in a dry and safe place away
from children’s reach.
- This electrical machine complies with related safety provisions.
Repairs shall be carried out exclusively by a skilled technician,
using exclusively OEM spare parts, otherwise whoever uses the
machine could be in serious danger.
- Use a proper electric tool.
- Do not use low effective tools for heavy duty applications.
INTENDED USE
This machine is an electrical grinder for chains used in chain saws.
- Use the machine exclusively for the types of chains stated in the
technical data chart.
- Do not use the machine to cut or grind anything other than the
chains envisaged.
- The machine must not be used in corrosive or explosive
environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following improper or
incorrect use of the machine.
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tecomec MIDI Jolly wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info