Bedienungsanleitung Tecsun PL310 (Seite 12 von 16) (Englisch)

628128

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

AM BW (BANDWIDTH) BUTTON

Short press [AM BW] button to choose 6, 4, 3, 2, 1 kHz

bandwidth. This may help to reduce interference on some

frequencies. Using WIDE usually results in better audio

fidelity, while using narrow limits the audio fidelity somewhat.

You can use it in MW, LW and SW band.

TO STORE STATION

There are total 500 preset memories within PL-310. For

FM, MW, and LW, each band has 100 preset memories;

and 200 preset memories for SW.

1) ATS (Auto Tuning Storage) on FM

1. Turn on the radio, and fully extend the antenna.

2. Short press [FM] button to select FM band.

3. Long press on [FM] button with a "B" sound and

frequency is running on the display. All the available

stations will be stored in the memory automatically. After

the long "B--" sound to be heard, ATS is completed and

is in the status of memory address.

4. Then use the [TUNING] knob to tune around for those

stored stations.

MW, LW or SW ATS is as same as the FM ATS.

SYSTEM SETTING

Frequency range setting for FM

Turn off the radio, long press [FM SET] button, until 87.5-

108MHz, 64-108MHz, 76-108MHz, or 87-108MHz appears

in the display. Quickly keep pressing on the [FM SET]

button to select suitable frequency range for your local FM.

Changing the clock format

Turn off the radio, long press [12/24] button, until " "or

" " appears in the display. If " " appears in the

display, which means the clock system will be in the 12 hour

format.

Turn off the radio, long press [9/10kHz] button until "9kHz"

or "10kHz" appears in the display. By long pressing again,

the alternative band step would be shown. The temperature

is also shown on screen at the same time.

In general practice, the 10kHz is to be used for broadcasting

MW(AM) as well as the temperature in the degree of

Fahrenheit ( ) for the North America region.

In order to provide convenience to the end users, the

"10kHz" is default to be displayed with temperature in the

degree of Fahrenheit ( ) and for "9kHz" to be displayed

with temperature in the degree of Centigrade ( ) together.

If the display shows "10kHz" with degree of Fahrenheit ( ),

which means this radio is set to 10 kHz step for MW(AM)

with temperature in Fahrenheit ( ).

MW(AM) step setting

Method 4:

Method 5: Auto-scan memory (see page12)

Method 6: (see

page 12)

Manual memory search (see page 12 )

Direct key in the station address number

2) ATS (Auto Tuning Storage) on MW or LW

1. Press & release [MW/LW] button to select MW or LW.

2. Press & hold [MW/LW] button and followed a "B" sound

and ATS starts to scan the radio stations in MW or LW.

3)ATS (Auto Tuning Storage) on SW

1. Fully extended the antenna, then press and release SW

[ ] or [ ] button to select SW.

2. There are mode A & mode B in SW.

Mode A: press & hold [ ] button to scan all radio stations

within all meter bands.

Mode B: press & hold [ ] button to scan all radio stations

in present meter band only.

ATS (Auto Tuning Storage) on FM, MW, LW or SW band

www.tecsunradio.com hch@cantonmade.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tecsun PL310 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info